Hi,
I bought a DE10 and received a DE0-Nano-DB25 breakout board from Jens, a
subscriber of this list.
What I did until now was to create the different artifacts such as:
* uboot
* kernel (4.1.33-ltsi)
* rootfs (Debian Jessie)
I used the Altera/Intel toolchain 17.0 to compile a bitstream file from
the Terasic CD-Rom:
Demonstrations/SoC_FPGA/DE10_NANO_SoC_FB
I can load this demo file and program the FPGA.
What I would like to do next is to compile a bitstream file which
includes support for DE0-Nano-DB25.
It seems to me this is not yet available.
How can I merge
https://github.com/machinekit/mksocfpga/tree/master/HW/QuartusProjects/DE0_Nano_SoC_DB25
to the Terasic demonstration project DE10_NANO_SoC_FB easily? Can you
give me any hints on how to do this?
Best regards,
Mario
--
___ __ ___ __ ___ _ ______ __ _ __________________
Mario Scholz ___/_ __ www :_ ____ www.mario-scholz.de
_____________/_ __ xmpp: mario at im.trial-n-error.net
--
website: http://www.machinekit.io blog: http://blog.machinekit.io github:
https://github.com/machinekit
---
You received this message because you are subscribed to the Google Groups "Machinekit" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to machinekit+unsubscr...@googlegroups.com.
Visit this group at https://groups.google.com/group/machinekit.
For more options, visit https://groups.google.com/d/optout.
U-Boot SPL 2013.01.01 (Oct 01 2017 - 20:56:04)
BOARD : Altera SOCFPGA Cyclone V Board
CLOCK: EOSC1 clock 25000 KHz
CLOCK: EOSC2 clock 25000 KHz
CLOCK: F2S_SDR_REF clock 0 KHz
CLOCK: F2S_PER_REF clock 0 KHz
CLOCK: MPU clock 800 MHz
CLOCK: DDR clock 400 MHz
CLOCK: UART clock 100000 KHz
CLOCK: MMC clock 50000 KHz
CLOCK: QSPI clock 3125 KHz
RESET: WARM
INFO : Watchdog enabled
SDRAM: Initializing MMR registers
SDRAM: Calibrating PHY
SEQ.C: Preparing to start memory calibration
SEQ.C: CALIBRATION PASSED
SDRAM: 1024 MiB
ALTERA DWMMC: 0
reading u-boot.img
reading u-boot.img
U-Boot 2013.01.01-g239ae4d (Oct 01 2017 - 13:24:38)
CPU : Altera SOCFPGA Platform
BOARD : Altera SOCFPGA Cyclone V Board
I2C: ready
DRAM: 1 GiB
MMC: ALTERA DWMMC: 0
In: serial
Out: serial
Err: serial
Net: mii0
Hit any key to stop autoboot: 5 4 3 2 1 0
Waiting for PHY auto negotiation to complete. done
ENET Speed is 100 Mbps - FULL duplex connection
BOOTP broadcast 1
BOOTP broadcast 2
DHCP client bound to address 10.12.22.99
Using mii0 device
TFTP from server 10.12.22.1; our IP address is 10.12.22.99
Filename 'de10/bootscripts/sockit.scr'.
Load address: 0x100000
Loading: *#
1.1 MiB/s
done
Bytes transferred = 1186 (4a2 hex)
## Executing script at 00100000
Using mii0 device
TFTP from server 10.12.22.1; our IP address is 10.12.22.99
Filename 'de10/sockit/soc_system.rbf'.
Load address: 0x2000000
Loading: *#################################################################
#################################################################
####################
1.9 MiB/s
done
Bytes transferred = 2199000 (218dd8 hex)
Using mii0 device
TFTP from server 10.12.22.1; our IP address is 10.12.22.99
Filename 'de10/sockit/soc_system.dtb'.
Load address: 0x100
Loading: *##
1.7 MiB/s
done
Bytes transferred = 24450 (5f82 hex)
Using mii0 device
TFTP from server 10.12.22.1; our IP address is 10.12.22.99
Filename 'de10/kernel/4.1.33-ltsi_17.09.03_pr/zImage'.
Load address: 0x8000
Loading: *#################################################################
#################################################################
#################################################################
#################################################################
####################
1.9 MiB/s
done
Bytes transferred = 4110144 (3eb740 hex)
## Starting application at 0x3FF7957C ...
## Application terminated, rc = 0x0
## Flattened Device Tree blob at 00000100
Booting using the fdt blob at 0x00000100
Loading Device Tree to 03ff7000, end 03ffff81 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 4.1.33-ltsi-g0175aa1 (root@vagary-vm) (gcc version
7.1.1 20170707 (Linaro GCC 7.1-2017.08) ) #1 SMP Sun Oct 1 21:28:10 CEST 2017
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] Machine model: Terasic DE10 NANO
[ 0.000000] cma: Reserved 16 MiB at 0x3f000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 12 pages/cpu @eefc9000 s19596 r8192 d21364
u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 260624
[ 0.000000] Kernel command line: console=ttyS0,115200 ip=dhcp root=/dev/nfs
rw nfsroot=10.12.22.1:/srv/nfs/de10/rootfs,v3,tcp
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1014072K/1048576K available (6271K kernel code, 431K
rwdata, 1588K rodata, 428K init, 159K bss, 18120K reserved, 16384K
cma-reserved, 253952K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc07b4f20 (7860 kB)
[ 0.000000] .init : 0xc07b5000 - 0xc0820000 ( 428 kB)
[ 0.000000] .data : 0xc0820000 - 0xc088bc60 ( 432 kB)
[ 0.000000] .bss : 0xc088bc60 - 0xc08b3b10 ( 160 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] L2C: platform modifies aux control register: 0x02060000 ->
0x32460000
[ 0.000000] L2C: platform provided aux values permit register corruption.
[ 0.000000] L2C: DT/platform modifies aux control register: 0x02060000 ->
0x32460000
[ 0.000000] L2C-310 erratum 769419 enabled
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 cache controller enabled, 8 ways, 512 kB
[ 0.000000] L2C-310: CACHE_ID 0x410030c9, AUX_CTRL 0x76460001
[ 0.000000] clocksource timer: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 19112604467 ns
[ 0.000006] sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every
21474836475ns
[ 0.000431] Console: colour dummy device 80x30
[ 0.000454] Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816)
[ 0.090279] pid_max: default: 32768 minimum: 301
[ 0.090378] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.090391] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.090956] CPU: Testing write buffer coherency: ok
[ 0.090985] ftrace: allocating 20973 entries in 62 pages
[ 0.122926] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.123170] Setting up static identity map for 0x8280 - 0x82d8
[ 0.160265] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.160332] Brought up 2 CPUs
[ 0.160348] SMP: Total of 2 processors activated (3188.32 BogoMIPS).
[ 0.160355] CPU: All CPU(s) started in SVC mode.
[ 0.160807] devtmpfs: initialized
[ 0.166879] VFP support v0.3: implementor 41 architecture 3 part 30 variant
9 rev 4
[ 0.167165] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 19112604462750000 ns
[ 0.169494] NET: Registered protocol family 16
[ 0.171213] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.178954] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint
registers.
[ 0.178968] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.213446] vgaarb: loaded
[ 0.213697] SCSI subsystem initialized
[ 0.214012] usbcore: registered new interface driver usbfs
[ 0.214081] usbcore: registered new interface driver hub
[ 0.214145] usbcore: registered new device driver usb
[ 0.214307] sopc@0:usbphy@0 supply vcc not found, using dummy regulator
[ 0.215329] pps_core: LinuxPPS API ver. 1 registered
[ 0.215340] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo
Giometti <giome...@linux.it>
[ 0.215373] PTP clock support registered
[ 0.215584] FPGA manager framework
[ 0.216839] Switched to clocksource timer
[ 0.252140] NET: Registered protocol family 2
[ 0.252752] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.252832] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.252958] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.253039] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.253084] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.253269] NET: Registered protocol family 1
[ 0.253605] RPC: Registered named UNIX socket transport module.
[ 0.253616] RPC: Registered udp transport module.
[ 0.253622] RPC: Registered tcp transport module.
[ 0.253628] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.254199] CPU PMU: Failed to parse /sopc@0/pmu0/interrupt-affinity[0]
[ 0.254239] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7
counters available
[ 0.255108] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.266330] NFS: Registering the id_resolver key type
[ 0.266381] Key type id_resolver registered
[ 0.266390] Key type id_legacy registered
[ 0.266460] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.266887] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.268194] bounce: pool size: 64 pages
[ 0.268213] io scheduler noop registered (default)
[ 0.272509] dma-pl330 ffe01000.dma: Loaded driver for PL330 DMAC-341330
[ 0.272527] dma-pl330 ffe01000.dma: DBUFF-512x8bytes Num_Chans-8
Num_Peri-32 Num_Events-8
[ 0.277787] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.279161] console [ttyS0] disabled
[ 0.279198] ffc02000.serial: ttyS0 at MMIO 0xffc02000 (irq = 24, base_baud =
6250000) is a 16550A
[ 0.867866] console [ttyS0] enabled
[ 0.873188] brd: module loaded
[ 0.878767] CAN device driver interface
[ 0.883180] stmmaceth ff702000.ethernet: snps,phy-addr property is deprecated
[ 0.890463] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 0.895493] Ring mode enabled
[ 0.898554] DMA HW capability register supported
[ 0.903064] Enhanced/Alternate descriptors
[ 0.907420] Enabled extended descriptors
[ 0.911411] RX Checksum Offload Engine supported (type 2)
[ 0.916878] TX Checksum insertion supported
[ 0.921127] Enable RX Mitigation via HW Watchdog Timer
[ 0.932449] libphy: stmmac: probed
[ 0.935845] eth0: PHY ID 00221622 at 1 IRQ POLL (stmmac-0:01) active
[ 0.942628] ffb40000.usb supply vusb_d not found, using dummy regulator
[ 0.949280] ffb40000.usb supply vusb_a not found, using dummy regulator
[ 0.986821] dwc2 ffb40000.usb: EPs: 16, dedicated fifos, 8064 entries in
SPRAM
[ 1.846960] dwc2 ffb40000.usb: DWC OTG Controller
[ 1.851674] dwc2 ffb40000.usb: new USB bus registered, assigned bus number 1
[ 1.858733] dwc2 ffb40000.usb: irq 36, io mem 0x00000000
[ 1.864199] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.870975] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.878175] usb usb1: Product: DWC OTG Controller
[ 1.882862] usb usb1: Manufacturer: Linux 4.1.33-ltsi-g0175aa1 dwc2_hsotg
[ 1.889628] usb usb1: SerialNumber: ffb40000.usb
[ 1.894801] hub 1-0:1.0: USB hub found
[ 1.898587] hub 1-0:1.0: 1 port detected
[ 1.903052] usbcore: registered new interface driver usb-storage
[ 1.909418] mousedev: PS/2 mouse device common for all mice
[ 1.915277] i2c /dev entries driver
[ 1.919529] watchdog: Invalid min and max timeout values, resetting to 0!
[ 1.926726] Synopsys Designware Multimedia Card Interface Driver
[ 1.932983] dw_mmc ff704000.flash: IDMAC supports 32-bit address mode.
[ 1.939573] dw_mmc ff704000.flash: Using internal DMA controller.
[ 1.945648] dw_mmc ff704000.flash: Version ID is 240a
[ 1.950730] dw_mmc ff704000.flash: DW MMC controller at irq 35, 32 bit host
data width, 1024 deep fifo
[ 1.960172] dw_mmc ff704000.flash: Got CD GPIO
[ 1.996885] dw_mmc ff704000.flash: 1 slots initialized
[ 2.003139] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.009396] usbcore: registered new interface driver usbhid
[ 2.014947] usbhid: USB HID core driver
[ 2.019492] altera_hps2fpga_bridge sopc@0:fpgabridge@0: fpga bridge
[hps2fpga] registered
[ 2.027913] altera_hps2fpga_bridge sopc@0:fpgabridge@1: fpga bridge
[lwhps2fpga] registered
[ 2.036384] altera_hps2fpga_bridge sopc@0:fpgabridge@2: fpga bridge
[fpga2hps] registered
[ 2.044980] altera_fpga2sdram_bridge sopc@0:fpgabridge@3: fpga bridge
[fpga2sdram] registered
[ 2.053499] altera_fpga2sdram_bridge sopc@0:fpgabridge@3: driver initialized
with handoff 000001ff
[ 2.062934] oprofile: using arm/armv7-ca9
[ 2.067950] NET: Registered protocol family 10
[ 2.073319] sit: IPv6 over IPv4 tunneling driver
[ 2.078572] NET: Registered protocol family 17
[ 2.083041] NET: Registered protocol family 15
[ 2.087506] can: controller area network core (rev 20120528 abi 9)
[ 2.093721] NET: Registered protocol family 29
[ 2.098171] can: raw protocol (rev 20120528)
[ 2.102429] can: broadcast manager protocol (rev 20120528 t)
[ 2.108086] can: netlink gateway (rev 20130117) max_hops=1
[ 2.113784] 8021q: 802.1Q VLAN Support v1.8
[ 2.118037] Key type dns_resolver registered
[ 2.122382] ThumbEE CPU extension supported.
[ 2.126660] Registering SWP/SWPB emulation handler
[ 2.132520] of_cfs_init
[ 2.135021] of_cfs_init: OK
[ 2.138972] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req
50000000Hz, actual 50000000HZ div = 0)
[ 2.148758] mmc0: new high speed SDHC card at address 59b4
[ 2.154591] mmcblk0: mmc0:59b4 USDU1 29.5 GiB
[ 2.160235] mmcblk0: p1 p2 p3
[ 2.246858] Sending DHCP requests ..
[ 5.217373] stmmaceth ff702000.ethernet eth0: Link is Up - 100Mbps/Full -
flow control off
[ 8.346790] ., OK
[ 8.396807] IP-Config: Got DHCP answer from 10.12.22.1, my address is
10.12.22.99
[ 8.404451] IP-Config: Complete:
[ 8.407703] device=eth0, hwaddr=00:ca:fe:ba:be:00, ipaddr=10.12.22.99,
mask=255.255.255.0, gw=10.12.22.1
[ 8.417587] host=10.12.22.99, domain=, nis-domain=(none)
[ 8.423309] bootserver=10.12.22.1, rootserver=10.12.22.1, rootpath=
[ 8.429820] nameserver0=10.12.22.1
[ 8.434163] ttyS0 - failed to request DMA
[ 8.454352] VFS: Mounted root (nfs filesystem) on device 0:15.
[ 8.461190] devtmpfs: mounted
[ 8.464515] Freeing unused kernel memory: 428K (c07b5000 - c0820000)
[ 9.103043] systemd[1]: System time before build time, advancing clock.
[ 9.139300] systemd[1]: Failed to insert module 'autofs4': No such file or
directory
[ 9.178383] random: systemd urandom read with 13 bits of entropy available
[ 9.195354] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT
+SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS
+ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 9.213686] systemd[1]: Detected architecture arm.
Welcome to [1mDebian GNU/Linux 9 (stretch)[0m!
[ 9.240363] systemd[1]: Set hostname to <de10nano4cnc>.
[ 9.913746] systemd[1]: Started Forward Password Requests to Wall Directory
Watch.
[[0;32m OK [0m] Started Forward Password Requests to Wall Directory Watch.
[ 9.938446] systemd[1]: Listening on Journal Socket (/dev/log).
[[0;32m OK [0m] Listening on Journal Socket (/dev/log).
[ 9.957294] systemd[1]: Created slice System Slice.
[[0;32m OK [0m] Created slice System Slice.
[ 9.977316] systemd[1]: Created slice system-getty.slice.
[[0;32m OK [0m] Created slice system-getty.slice.
[ 9.998347] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[[0;32m OK [0m] Listening on /dev/initctl Compatibility Named Pipe.
[ 10.027099] systemd[1]: Listening on udev Kernel Socket.
[[0;32m OK [0m] Listening on udev Kernel Socket.
[ 10.048938] systemd[1]: Mounting Debug File System...
Mounting Debug File System...
[ 10.067277] systemd[1]: Reached target Remote File Systems.
[[0;32m OK [0m] Reached target Remote File Systems.
[ 10.087197] systemd[1]: Reached target Slices.
[[0;32m OK [0m] Reached target Slices.
[ 10.107305] systemd[1]: Listening on Syslog Socket.
[[0;32m OK [0m] Listening on Syslog Socket.
[ 10.127218] systemd[1]: dev-hugepages.mount: Couldn't determine result for
ConditionVirtualization=!private-users, assuming failed: No such file or
directory
[ 10.141686] systemd[1]: Listening on Journal Socket.
[[0;32m OK [0m] Listening on Journal Socket.
[ 10.169177] systemd[1]: Starting Create Static Device Nodes in /dev...
Starting Create Static Device Nodes in /dev...
[ 10.213227] systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
[ 10.239437] systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
[ 10.306724] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 10.330263] systemd[1]: Listening on udev Control Socket.
[[0;32m OK [0m] Listening on udev Control Socket.
[ 10.357358] systemd[1]: Reached target Sockets.
[[0;32m OK [0m] Reached target Sockets.
[ 10.377533] systemd[1]: Created slice system-serial\x2dgetty.slice.
[[0;32m OK [0m] Created slice system-serial\x2dgetty.slice.
[ 10.397504] systemd[1]: Started Dispatch Password Requests to Console
Directory Watch.
[[0;32m OK [0m] Started Dispatch Password Requests to Console Directory
Watch.
[ 10.427121] systemd[1]: Reached target Encrypted Volumes.
[[0;32m OK [0m] Reached target Encrypted Volumes.
[ 10.458667] systemd[1]: Reached target Swap.
[[0;32m OK [0m] Reached target Swap.
[ 10.477151] systemd[1]: Reached target Paths.
[[0;32m OK [0m] Reached target Paths.
[ 10.498545] systemd[1]: Mounted Debug File System.
[[0;32m OK [0m] Mounted Debug File System.
[ 10.527397] systemd[1]: Started Journal Service.
[[0;32m OK [0m] Started Journal Service.
[[0;32m OK [0m] Started Create Static Device Nodes in /dev.
[[0;32m OK [0m] Started Load Kernel Modules.
[[0;32m OK [0m] Started Remount Root and Kernel File Systems.
Starting Load/Save Random Seed...
Starting udev Coldplug all Devices...
Mounting Configuration File System...
Starting Apply Kernel Variables...
Starting udev Kernel Device Manager...
[[0;32m OK [0m] Reached target Local File Systems (Pre).
Mounting /tmp...
Starting Flush Journal to Persistent Storage...
[[0;32m OK [0m] Mounted Configuration File System.
[[0;32m OK [0m] Mounted /tmp.
[[0;32m OK [0m] Started Load/Save Random Seed.
[[0;32m OK [0m] Started Apply Kernel Variables.
[[0;32m OK [0m] Reached target Local File Systems.
Starting Raise network interfaces...
[ 10.981016] systemd-journald[697]: Received request to flush runtime journal
from PID 1
[[0;32m OK [0m] Started Flush Journal to Persistent Storage.
Starting Create Volatile Files and Directories...
[[0;32m OK [0m] Started udev Coldplug all Devices.
[[0;32m OK [0m] Started udev Kernel Device Manager.
[[0;32m OK [0m] Started Create Volatile Files and Directories.
Starting Network Time Synchronization...
Starting Update UTMP about System Boot/Shutdown...
[[0;32m OK [0m] Found device /dev/ttyS0.
[[0;32m OK [0m] Started Network Time Synchronization.
[[0;32m OK [0m] Started Update UTMP about System Boot/Shutdown.
[[0;32m OK [0m] Started Raise network interfaces.
[[0;32m OK [0m] Reached target Network.
[[0;32m OK [0m] Reached target Network is Online.
[[0;32m OK [0m] Reached target System Initialization.
[[0;32m OK [0m] Started Daily Cleanup of Temporary Directories.
[[0;32m OK [0m] Reached target Basic System.
Starting Permit User Sessions...
Starting getty on tty2-tty6 if dbus and logind are not available...
[[0;32m OK [0m] Started Regular background program processing daemon.
Starting System Logging Service...
[[0;32m OK [0m] Reached target System Time Synchronized.
[[0;32m OK [0m] Started Daily apt download activities.
[[0;32m OK [0m] Started Daily apt upgrade and clean activities.
[[0;32m OK [0m] Reached target Timers.
[[0;32m OK [0m] Started Permit User Sessions.
[[0;32m OK [0m] Started System Logging Service.
[[0;32m OK [0m] Started getty on tty2-tty6 if dbus and logind are not
available.
[[0;32m OK [0m] Started Getty on tty6.
[[0;32m OK [0m] Started Getty on tty5.
[[0;32m OK [0m] Started Getty on tty4.
[[0;32m OK [0m] Started Getty on tty3.
[[0;32m OK [0m] Started Getty on tty2.
[[0;32m OK [0m] Started Serial Getty on ttyS0.
[[0;32m OK [0m] Started Getty on tty1.
[[0;32m OK [0m] Reached target Login Prompts.
[[0;32m OK [0m] Reached target Multi-User System.
[[0;32m OK [0m] Reached target Graphical Interface.
Starting Update UTMP about System Runlevel Changes...
[[0;32m OK [0m] Started Update UTMP about System Runlevel Changes.
Debian GNU/Linux 9 de10nano4cnc ttyS0
de10nano4cnc login: