I was checking out the web site of a Puerto Rican makerspace a couple of days ago at our makerspace.. The blog was ominously silent since the hurricane.
On Oct 2, 2017 9:45 AM, "gary" <[email protected]> wrote: > > sounds good I am in cape coral fl,,, > I also got lucky some pool cage screens and branches that's about it best > thing I never lost power and had about 50 gallons on gas > waiting to run the generator go's in the lawn mower now... > gary > > On Thursday, September 14, 2017 at 12:54:42 PM UTC-4, Daren Schwenke wrote: > >> Damage from Irma: About 2 cubic yards of tree branches around the yard >> and everything was dirty. The wind pushed water through the windows which >> were not covered/sealed in minor amounts. That was about it. We did get >> lucky that it broke inland and the winds that got us were coming from >> across land. >> Cleanup from the preparations was/is more labor intensive than the >> hurricane itself. The ice blocks for the fridge are still melting in the >> sink 4 days later. We never lost power. >> >> On Thursday, September 14, 2017 at 7:43:02 AM UTC-4, Tom M wrote: >>> >>> Oh boy.. see you around the next event. (Did you take any damage from >>> Irma?) >>> I'm trying to get switched over to Charles probotix solution on my >>> MPCNC. I'm currently running gantrykins and I keep forgetting to switch >>> between world and joint when I'm homing. I wind up inadvertently racking >>> the gantries. I cracked some of 3d printed bearing blocks. Luckily weld >>> repairing them is fairly easy. >>> Switches are wired and installed I need to install terminals, and hook >>> into the cramps and redo the Hal and ini's. Yikes, I'm running out of time >>> here. >>> >>> >>> >>> On Sep 14, 2017 2:47 AM, "Daren Schwenke" <[email protected]> wrote: >>> >>>> I'm at my other home in FL currently and crashed the head on the >>>> printer, destroying part of the head and splitting my ceramic bed. Nema23 >>>> and 9mm belts may have been a bad choice. >>>> >>>> Tried updating to use the new pythonic configs and it turns out in the >>>> current fdm module (without using the subdirectory to override it like in >>>> the Rostock config I borrowed from machinekoder) the delta_r or rod length >>>> is ignored. So 0,0,0 was below the bed. I slowly approached it, but the >>>> interface didn't register my stop command until it was too late... so I got >>>> to watch it slowly destroy my bed. :) >>>> My fault for removing the physical estop button for aesthetic reasons.. >>>> >>>> Prime is screwy due to Irma so parts wouldn't get here in time for me >>>> to fabricate them, and I can't find a suitable polished ceramic tile >>>> locally. >>>> So... I'm not going. >>>> >>>> On Sunday, September 10, 2017 at 9:35:37 PM UTC-4, Tom M wrote: >>>>> >>>>> >>>>> Hey Guy's, >>>>> >>>>> If anyone is going to be at the Milwaukee Maker Faire feel free to >>>>> stop by and say hi. >>>>> >>>>> https://milwaukee.makerfaire.com/maker/entry/275/ >>>>> >>>>> Daren Schewenke is going to be there as well. >>>>> https://milwaukee.makerfaire.com/maker/entry/277/ >>>>> >>>>> Tom >>>>> >>>> -- >>>> website: http://www.machinekit.io blog: http://blog.machinekit.io >>>> github: https://github.com/machinekit >>>> --- >>>> You received this message because you are subscribed to a topic in the >>>> Google Groups "Machinekit" group. >>>> To unsubscribe from this topic, visit https://groups.google.com/d/to >>>> pic/machinekit/Z84ZyZTkfe4/unsubscribe. >>>> To unsubscribe from this group and all its topics, send an email to >>>> [email protected]. >>>> Visit this group at https://groups.google.com/group/machinekit. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> -- > website: http://www.machinekit.io blog: http://blog.machinekit.io github: > https://github.com/machinekit > --- > You received this message because you are subscribed to a topic in the > Google Groups "Machinekit" group. > To unsubscribe from this topic, visit https://groups.google.com/d/ > topic/machinekit/Z84ZyZTkfe4/unsubscribe. > To unsubscribe from this group and all its topics, send an email to > [email protected]. > Visit this group at https://groups.google.com/group/machinekit. > For more options, visit https://groups.google.com/d/optout. > -- website: http://www.machinekit.io blog: http://blog.machinekit.io github: https://github.com/machinekit --- You received this message because you are subscribed to the Google Groups "Machinekit" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. Visit this group at https://groups.google.com/group/machinekit. For more options, visit https://groups.google.com/d/optout.
