James,
Remove the thrust bearing carrier and the front bearing circlips Remove the
housing from the steel centre plate forward. This is where all 71 series
boxes split.
Cheers
Feral Errol
WWW.Datrats.com.au
----------
From: jamesf <[EMAIL PROTECTED]>
To: [EMAIL PROTECTED]
Subject: Re: NEEDED Z-18et COMPUTER AND WIRING HARNESS
Date: Thursday, November 16, 2000 21:52
>From the center split??
cause with all the Z18 boxes I have seen you can't remove the
bellhousing??
Errol Smith wrote:
> Daniel,
> Fit a Z18 bell housing to the box.
> Cheers
> Feral Errol
> WWW.Datrats.com.au
>
> ----------
> From: Daniel Kroehn <[EMAIL PROTECTED]>
> To: [EMAIL PROTECTED]
> Subject: Re: NEEDED Z-18et COMPUTER AND WIRING HARNESS
> Date: Thursday, November 16, 2000 11:47
>
> Errol,
>
> What exactly has to be done to get the head sitting on the right angle?
> Also will this affect the position of the gearbox relative to its current
> postion?
>
> Daniel Kroehn
>
> Supporting Datrats
> WWW.Datrats.com.au
>
> ----- Original Message -----
> From: Errol Smith <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Sent: Thursday, November 16, 2000 6:08 AM
> Subject: Re: NEEDED Z-18et COMPUTER AND WIRING HARNESS
>
> > Mick,
> > Well it is a straight bolt up, but needs to be bolted in a slightly
> > different position. Nothing too difficult.
> > Cheers
> > Feral Errol
> > WWW.Datrats.com.au
> >
> > ----------
> > From: Mick Ralph <[EMAIL PROTECTED]>
> > To: [EMAIL PROTECTED]
> > Subject: Re: NEEDED Z-18et COMPUTER AND WIRING HARNESS
> > Date: Wednesday, November 15, 2000 23:26
> >
> > Errol
> > I thought that the Z head would be almost a straight bolt up type of
set
> > up.
> > You (I) learn something new every day..
> > thanks mate
> > cheers
> > Mick
> >
> > ----- Original Message -----
> > From: Errol Smith <[EMAIL PROTECTED]>
> > To: <[EMAIL PROTECTED]>
> > Sent: Wednesday, November 15, 2000 5:03 PM
> > Subject: Re: NEEDED Z-18et COMPUTER AND WIRING HARNESS
> >
> >
> > > Mick,
> > > Thats a good idea, but you need to decompress your L series before
> > fitting
> > > the Z18ET head and manifolds. You should also change the angle of the
> > block
> > > as the oil returns need the block to be inclined to prevent oil build
> up
> > > over the valve stem seals
> > > Cheers
> > > Feral Errol
> > > WWW.Datrats.com.au
> > >
> > > ----------
> > > From: Mick Ralph <[EMAIL PROTECTED]>
> > > To: [EMAIL PROTECTED]
> > > Subject: Re: NEEDED Z-18et COMPUTER AND WIRING HARNESS
> > > Date: Wednesday, November 15, 2000 12:37
> > >
> > > Daniel
> > > U could just put a Z head onto an L series block.. then u could keep
> the
> > > same gearbox and even the same engine number..
> > > I think thats what i am going to do
> > > cheers
> > > mick
> > >
> > > ----- Original Message -----
> > > From: Daniel Kroehn
> > > To: [EMAIL PROTECTED]
> > > Sent: Monday, November 13, 2000 4:07 PM
> > > Subject: Re: NEEDED Z-18et COMPUTER AND WIRING HARNESS
> > >
> > >
> > > Thanks for that Zac, a few people had told me otherwise. I think
> I'll
> > > have to go for an aftermarket comp. or find a complete package, not
> > having
> > > much luck though.
> > >
> > > Daniel Kroehn
> > > ----- Original Message -----
> > > From: Zac Campbell
> > > To: [EMAIL PROTECTED]
> > > Sent: Monday, November 13, 2000 3:13 PM
> > > Subject: Re: NEEDED Z-18et COMPUTER AND WIRING HARNESS
> > >
> > >
> > > Sorry, but you do need a gearbox!
> > > The Z18 sits on an angle (8 degrees from memory) and thus the
gear
> > > selector will point towards the passenger.
> > > I have seen a Z18 in a 1600 with an L-series box, but the owner
had
> > > angled the engine instaed. it looked hideous. 1/2 the strut tower was
> > > sledge hammered to clear the inlet manifold!
> > >
> > > zac
> > >
> > > ----- Original Message -----
> > > From: Daniel Kroehn
> > > To: [EMAIL PROTECTED]
> > > Sent: Monday, November 13, 2000 1:50 PM
> > > Subject: NEEDED Z-18et COMPUTER AND WIRING HARNESS
> > >
> > >
> > > List,
> > >
> > > I've found a Z-18et for a really good price without the box or
> the
> > > computer and harness. Everything else is there. I already have a
few
> L
> > > series boxes at home so I don't need a gearbox but I do need a
HARNESS
> > and
> > > COMPUTER. If any of you guys who have put aftermarket computer on
your
> > > zeds have one lying around and are willing to sell it, could you
write
> > > back.
> > >
> > > I JUST DON'T WANT TO LET THIS ONE SLIP THROUGH MY FINGERS, BUT
> I'LL
> > > HAVE TO IF I CAN'T GET A COMPUTER AND HARNESS
> > >
> > > Thanks
> > >
> > >
> > > Daniel Kroehn
> > >
> > >
> > --membersozdat------------------------------------------------------
> > -
> > >
> > > OZDAT Mailing List Please Note:-
> > > Send (un)subscribe requests to [EMAIL PROTECTED]
> > > Send submissions to [EMAIL PROTECTED]
> > > No unauthorised redistribution of this email
> > > http://www.ozdat.com/ozdatonline/index.htm
> > > http://www.ozdat.com/ozdatonline/listindex.html
> > > http://www.mail-archive.com/[email protected]/
> > >
> > --------------------------------------------------------------------
> > -
> > >
> >
> --membersozdat-------------------------------------------------------
> > > OZDAT Mailing List Please Note:-
> > > Send (un)subscribe requests to [EMAIL PROTECTED]
> > > Send submissions to [EMAIL PROTECTED]
> > > No unauthorised redistribution of this email
> > > http://www.ozdat.com/ozdatonline/index.htm
> > > http://www.ozdat.com/ozdatonline/listindex.html
> > > http://www.mail-archive.com/[email protected]/
> >
> ---------------------------------------------------------------------
> > >
> > >
--membersozdat-------------------------------------------------------
> > > OZDAT Mailing List Please Note:-
> > > Send (un)subscribe requests to [EMAIL PROTECTED]
> > > Send submissions to [EMAIL PROTECTED]
> > > No unauthorised redistribution of this email
> > > http://www.ozdat.com/ozdatonline/index.htm
> > > http://www.ozdat.com/ozdatonline/listindex.html
> > > http://www.mail-archive.com/[email protected]/
> > >
---------------------------------------------------------------------
> > >
> > >
> > >
> >
> >
> >
>
--
________________________________________________________________________
James Fitness
Director
Data Scribe Australia Pty Ltd
http://www.datascribe.com.au
Computers and Supplies
OZDAT Online
http://www.datascribe.com.au/ozdatonline/index.htm
--membersozdat-------------------------------------------------------
OZDAT Mailing List Please Note:-
Send (un)subscribe requests to [EMAIL PROTECTED]
Send submissions to [EMAIL PROTECTED]
No unauthorised redistribution of this email
http://www.ozdat.com/ozdatonline/index.htm
http://www.ozdat.com/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------
