Thanks for clearing that up.. just trying to get it all the info straight for
a spreadsheet I have been working on...
So just to clarify then... the Z22 Crank will fit into a L20 Block, with
the only machining being - clearancing rods/counterweights of the block?
cya
JamesF
Errol Smith wrote:
> James,
> As Tom has pointed out the post was confused as was I at the time obviously.
> I was cut and pasting measurements and made a mistake. The measurements Tom
> gave are correct by me.
>
> Cheers
> Feral Errol
> mailto:[EMAIL PROTECTED]
> http://www.datrats.com.au/
>
> -----Original Message-----
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED]]On Behalf Of jamesf
> Sent: Thursday, May 10, 2001 11:36 AM
> To: [EMAIL PROTECTED]
> Subject: Re: L 13 RODS
> Hi Errol
>
> Not trying to be picky... just want to clear it up but in a previous post
> you mentioned the following
>
> L13, 14, 16 & 18 are 54.942mm same as L24 and L26 All the following rods
> use a 59.942mm crank journal.
> L20B 145.9mm, LZ20 152.45, LZ22 145.9, LZ24 143.9
> (copy of old message attached below):-
>
> So was that previous email actually referring to the mains... and not the
> big ends??
>
> regards
> James
>
> Errol Smith wrote:
>
> > James,
> > L13, 14, 16 & 18 are 54.942mm same as L24 and L26
> > Cheers
> > Feral Errol
> > ----------
> > From: jamesf <[EMAIL PROTECTED]>
> > To: [EMAIL PROTECTED]
> > Subject: Re: time to build L20 turbo
> > Date: Thursday, October 12, 2000 2:21
> >
> > I noticed you didn't mention the L18/L16 rods here....What size is the
> > crank journal from those?
> >
> > JamesF
> >
> > Errol Smith wrote:
> >
> > > Andrew,
> > > All the following rods use a 59.942mm crank journal.
> > > L20B 145.9mm, LZ20 152.45, LZ22 145.9, LZ24
> > > 143.9
> > > As you can see the only rod with some potential for lowering comp is the
> > > LZ24, even then only 2 mm.
> > > I personally would have gone for lower compression height pistons, (30
> or
> > > 32mm compression height vs the normal 37.1mm).
> >
> >
>
> Errol Smith wrote:
>
> > James,
> > All Lseries and LZ and FJ engines use the same diameter crank journal for
> > the big ends.
> > I think the Z24ET would be good for 5800 - 6000 rpm reliably. I guess
> torque
> > should be good with about 250ft/lb @ 4000 using a TO3 with 10 pound.
> > Cheers
> > Feral Errol
> > mailto:[EMAIL PROTECTED]
> > http://www.datrats.com.au/
> >
> > -----Original Message-----
> > From: [EMAIL PROTECTED]
> > [mailto:[EMAIL PROTECTED]]On Behalf Of jamesf
> > Sent: Thursday, May 10, 2001 2:07 AM
> > To: [EMAIL PROTECTED]
> > Subject: Re: L 13 RODS
> >
> > Hi Errol
> >
> > So the FJ Rods use a 59.942mm crank journal?
> > (with the L13's at 54mm, the FJ rods wouldn't be
> > any good for Robert's application)
> > Ummm..I like the sound of that Z24et combo ... what
> > sort of Max RPM do you reckon that bottom end could take?
> >
> > regards
> > James
> >
> > Errol Smith wrote:
> >
> > > Andrew,
> > > The FJ20DET rods are 140.5mm centre to centre as are the FJ20DE rods
> The
> > NA
> > > rods are not as strong through the beam. The DET rods are twice as wide
> in
> > > the beam as an L series rod. I just sent a set of DET rods to lister
> Mark
> > > Krawczuk in Renmark today for his Z24 cranked, L20B blocked, FJ20DET
> > rodded,
> > > Z18ET head and manifolds engine. I think he's about to open a huge can
> of
> > > whoop-Ass in Renmark.
> > >
> > > Cheers
> > > Feral Errol
> > > mailto:[EMAIL PROTECTED]
> > > http://www.datrats.com.au/
> > >
> > > -----Original Message-----
> > > From: [EMAIL PROTECTED]
> > > [mailto:[EMAIL PROTECTED]]On Behalf Of andrew smith
> > > Sent: Wednesday, May 09, 2001 10:28 AM
> > > To: [EMAIL PROTECTED]
> > > Subject: Re: L 13 RODS
> > >
> > > Tom
> > > I was told the FJ24 rod is the same length as an L16 at 133mm (could be
> > > wrong
> > > though).I'm almost sure the rods differ from n/a to turbo FJ20's (could
> be
> > > wrong again).
> > > Andrew Smith
> > >
> > > Tom Richardson wrote:
> > >
> > > > Andrew,
> > > >
> > > > For both, as far I know. Incidentally, FJ24 rods are the same
> according
> > > to
> > > > Honosowetz!
> > > >
> > > > - Tom
> > > >
> > > > ----- Original Message -----
> > > > From: "andrew smith" <[EMAIL PROTECTED]>
> > > > To: <[EMAIL PROTECTED]>
> > > > Sent: Tuesday, May 08, 2001 11:35 PM
> > > > Subject: Re: L 13 RODS
> > > >
> > > > > Tom,
> > > > > Is 140mm for the fjde or the fj20det rods.
> > > > > Andrew Smith
> > > > >
> > > > > Tom Richardson wrote:
> > > > >
> > > > > > Robert,
> > > > > >
> > > > > > FJ20 rods are 140mm (as opposed to 139.9mm L13) and match L series
> > > > > > crankshaft journals, but have 22mm wristpins. Give Craig Williams
> > > from
> > > > > > Maddat Motorsport a call on 0412 1600 25, he had a set of FJ20DET
> > rods
> > > > for
> > > > > > $50 a week or so ago.
> > > > > >
> > > > > > - Tom
> > > > > >
> > > > > > ----- Original Message -----
> > > > > > From: "robert hall" <[EMAIL PROTECTED]>
> > > > > > To: <[EMAIL PROTECTED]>
> > > > > > Sent: Monday, May 07, 2001 7:05 PM
> > > > > > Subject: L 13 RODS
> > > > > >
> > > > > > > HI, HAS anyone got any L13 rods to sell?
> > > > > > > i am willing to pay really good money for a set of four.
> > > > > > > urgently needed.
> > > > > > > phone 08-85866088
> > > > > > > fax 08-85864576
> > > > > > > mobile o415101996
> > > > > > >
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> > --
> > ________________________________________________________________________
> >
> > James Fitness
> > Director
> > Data Scribe Australia Pty Ltd
> > http://www.datascribe.com.au
> > Computers and Supplies
> >
> > OZDAT Online
> > http://www.ozdat.com/ozdatonline/index.htm
> >
>
> --
> ________________________________________________________________________
>
> James Fitness
> Director
> Data Scribe Australia Pty Ltd
> http://www.datascribe.com.au
> Computers and Supplies
>
> OZDAT Online
> http://www.ozdat.com/ozdatonline/index.htm
>
--
________________________________________________________________________
James Fitness
Director
Data Scribe Australia Pty Ltd
http://www.datascribe.com.au
Computers and Supplies
OZDAT Online
http://www.ozdat.com/ozdatonline/index.htm
--membersozdat-------------------------------------------------------
OZDAT Mailing List Please Note:-
Send (un)subscribe requests to [EMAIL PROTECTED]
Send submissions to [EMAIL PROTECTED]
No unauthorised redistribution of this email
http://www.ozdat.com/ozdatonline/index.htm
http://www.ozdat.com/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------
