Re: Z series blocks

[David Costello]

would that have problems with overheating?   Dave ----- Original Message ----- From: E Smith To: [EMAIL PROTECTED] Sent: Tuesday, January 14, 2003 6:15 PM Subject: RE: Z series blocks 90 would be the limit. I would go with 89 and have stiffer bores if it was my engine. Either that, or bore and sleeve the block to 92 mm. (approx $480 for 4 sleeves) Just another thought? Cheers, Feral Errol <http://www.datrats.com.au/> -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of David Costello Sent: Tuesday, January 14, 2003 11:38 AM To: [EMAIL PROTECTED] Subject: Re: Z series blocks would a Z22 be safe at 90mm running forced induction?   Dave ----- Original Message ----- From: E Smith To: [EMAIL PROTECTED] Sent: Monday, January 13, 2003 9:15 PM Subject: RE: Z series blocks   The Z22 block is a different casting that can be taken out to 89mm easily with plenty of meat left in the bores. A Z20 would be close to water then I would think?     Cheers, Feral Errol <http://www.datrats.com.au/> -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of David Costello Sent: Monday, January 13, 2003 9:06 PM To: [EMAIL PROTECTED] Subject: Z series blocks I've just been looking at the specs for a few different Z series bits and pieces and noticed that the Z20 and Z22 blocks appear to be the same, they're the same deckheight, but the Z20 is 85mm bore and the Z22 is 88mm bore ..... is the Z22 block just a bored out Z20 block? is it safe to take a Z20 block out that far? has anyone ever tried this?   Dave --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ ---------------------------------------------------------------------