For rally use I would think that the stock 13/16 master would be adequate with the single piston fronts even with disc rear fitted. If you upgrade the front calipers to larger piston area then you may have to look at an upgrade in master cylinder. Do some maths and compare the ratios of piston areas between front and rear pistons stock and what you are looking to fit. If you are going up by more than 15% in area either end, fit a larger cylinder.
Cheers Feral Errol Get Serious! http://www.datrats.com.au/ -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Warren Phillip-Clarke Sent: Saturday, March 20, 2004 5:50 AM To: [EMAIL PROTECTED] Subject: RE: Master Cylinder Here's my question I have a rally car, 180Bsss booster twin master cylinder type set up. I currently have a drum rear end, soon to make way for a disk conversion. Disks are from a pintara with bluebird GILROCK single piston callipers. Will I need to a) get a bigger M/C b) need to get a bias valve fitted? Any help guys is greatly appreciated. -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Brad Sent: Friday, 19 March 2004 9:32 PM To: [EMAIL PROTECTED] Subject: RE: Master Cylinder You may have a problem bleeding the system if you tilt the m/c. There is a small diameter booster in the 710 which may fit, if not you may have to look at fitting a remote booster. If you want to do it properly, fit twin m/c with an adjustable bias bar and don't run a booster. Dunno what your local transport dept will think of it though. -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of mark krawczuk Sent: Friday, 19 March 2004 11:12 PM To: [EMAIL PROTECTED] Subject: Re: Master Cylinder hi, on a 1600 with 4 wheel discs, would it be best to use a master cylinder with a porportioning valve in it , or just use the standard twin resevoir setup? i`ve been looking at using the large 180b booster, and a vn ? commodore m/c in my 1600 with the sr. its pretty well touch-n-go with fitting , the only other way to have more clearance is to split the booster, fit two studs so that the m/c is mounted sideways, (then put it back together ) or twisted a bit. then i would have to put some fittings in the fluid holes and run a remote fluid container..... mark k ----- Original Message ----- From: "Errol Smith" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Friday, March 19, 2004 10:03 PM Subject: RE: Master Cylinder If you look at the cylinder area ratios I would be surprised if you needed a 1" with the skyline calipers as they have small pistons? Cheers Feral Errol Get Serious! http://www.datrats.com.au/ -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Jimmy Sent: Friday, March 19, 2004 9:11 PM To: [EMAIL PROTECTED] Subject: RE: Master Cylinder i got a 1" and it weighs about twice the amount of the 7/8 cylinder. same shape and size though. should be good for the 4spot skyline brakes. "Mohit K. Autar" <[EMAIL PROTECTED]> wrote: hi there, im also upgrading brakes on my datsun 1400 p.510.can anyone tell me what to use. -----Original Message----- From: Ben Holko [mailto:[EMAIL PROTECTED] Sent: Wednesday, February 18, 2004 3:53 PM To: [EMAIL PROTECTED] Subject: Master Cylinder Hey all, I'm in the middle of upgrading the brakes on the 180B SSS, and need to upgrade the master cylinder. I'll email details of exactly what I'm using for brakes once it's finished, but I am going to need at least a 1" master cylinder. Is there a 1" that will bolt straight on? The biggest I know of is 7/8. Has anyone gone bigger than 7/8 on your 510/610, and if so what did you use? thanks! Ben --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[EMAIL PROTECTED]/ ---------------------------------------------------------------------Thi s email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this mail in error, please notify the System Administrator. Please note that any views or opinions presented in this mail are solely those of the author and do not necessarily represent those of the Institute. Finally the recipient should check this mail and any attachment for the presence of viruses. FIT has a virus detection in place and makes every reasonable effort to ensure that this message is free f! rom viruses. FIT accepts no liability for any damage caused by any virus transmitted by this mail _____ Find local movie times and trailers on Yahoo! Movies. <http://au.rd.yahoo.com/mail/tagline/*http://au.movies.yahoo.com> --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[EMAIL PROTECTED]/ --------------------------------------------------------------------- ------=_NextPart_000_0003_01C40E02.434D9D60 Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable <html xmlns:v=3D"urn:schemas-microsoft-com:vml" = xmlns:o=3D"urn:schemas-microsoft-com:office:office" = xmlns:w=3D"urn:schemas-microsoft-com:office:word" = xmlns=3D"http://www.w3.org/TR/REC-html40";> <head> <meta http-equiv=3DContent-Type content=3D"text/html; = charset=3Diso-8859-1"> <meta name=3DProgId content=3DWord.Document> <meta name=3DGenerator content=3D"Microsoft Word 9"> <meta name=3DOriginator content=3D"Microsoft Word 9"> <link rel=3DFile-List href=3D"cid:[EMAIL PROTECTED]"> <link rel=3DEdit-Time-Data href=3D"cid:[EMAIL PROTECTED]"> <!--[if !mso]> <style> v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} </style> <![endif]--><!--[if gte mso 9]><xml> <o:OfficeDocumentSettings> <o:DoNotRelyOnCSS/> </o:OfficeDocumentSettings> </xml><![endif]--><!--[if gte mso 9]><xml> <w:WordDocument> <w:Zoom>0</w:Zoom> <w:DocumentKind>DocumentEmail</w:DocumentKind> <w:EnvelopeVis/> </w:WordDocument> </xml><![endif]--> <style> <!-- /* Font Definitions */ @font-face {font-family:Tahoma; panose-1:2 11 6 4 3 5 4 4 2 4; mso-font-charset:0; mso-generic-font-family:swiss; mso-font-pitch:variable; mso-font-signature:16792199 0 0 0 65791 0;} /* Style Definitions */ p.MsoNormal, li.MsoNormal, div.MsoNormal {mso-style-parent:""; margin:0cm; margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:12.0pt; font-family:"Times New Roman"; mso-fareast-font-family:"Times New Roman";} a:link, span.MsoHyperlink {color:blue; text-decoration:underline; text-underline:single;} a:visited, span.MsoHyperlinkFollowed {color:blue; text-decoration:underline; text-underline:single;} p.MsoAutoSig, li.MsoAutoSig, div.MsoAutoSig {margin:0cm; margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:12.0pt; font-family:"Times New Roman"; mso-fareast-font-family:"Times New Roman";} p {margin-right:0cm; mso-margin-top-alt:auto; mso-margin-bottom-alt:auto; margin-left:0cm; mso-pagination:widow-orphan; font-size:12.0pt; font-family:"Times New Roman"; mso-fareast-font-family:"Times New Roman";} span.EmailStyle18 {mso-style-type:personal-reply; mso-ansi-font-size:10.0pt; mso-ascii-font-family:Arial; mso-hansi-font-family:Arial; mso-bidi-font-family:Arial; color:navy;} @page Section1 {size:612.0pt 792.0pt; margin:72.0pt 90.0pt 72.0pt 90.0pt; mso-header-margin:36.0pt; mso-footer-margin:36.0pt; mso-paper-source:0;} div.Section1 {page:Section1;} --> </style> </head> <body lang=3DEN-US link=3Dblue vlink=3Dblue = style=3D'tab-interval:36.0pt'> <div class=3DSection1> <p class=3DMsoNormal><span class=3DEmailStyle18><font size=3D2 = color=3Dnavy face=3DArial><span style=3D'font-size:10.0pt;mso-bidi-font-size:12.0pt;font-family:Arial'>I f= you look at the cylinder area ratios I would be surprised if you needed a = 1” with the skyline calipers as they have small = pistons?<o:p></o:p></span></font></span></p> <p class=3DMsoNormal><span class=3DEmailStyle18><font size=3D2 = color=3Dnavy face=3DArial><span style=3D'font-size:10.0pt;mso-bidi-font-size:12.0pt;font-family:Arial'>< != [if = !supportEmptyParas]> <![endif]><o:p></o:p></span></font></span></p> <p class=3DMsoAutoSig><!--[if supportFields]><span = class=3DEmailStyle18><font=20 size=3D2 color=3Dnavy face=3DArial><span = style=3D'font-size:10.0pt;mso-bidi-font-size: 12.0pt;font-family:Arial'><span = style=3D'mso-element:field-begin'></span><span=20 style=3D"mso-spacerun: yes"> </span>AUTOTEXTLIST \s "E-mail=20 Signature" <span = style=3D'mso-element:field-separator'></span></span></font></span><![end i= f]--><font size=3D2 color=3Dblue face=3DArial><span = style=3D'font-size:10.0pt;mso-bidi-font-size: 12.0pt;font-family:Arial;color:blue'>Cheers<o:p></o:p></span></font></p> <p class=3DMsoAutoSig><font size=3D2 color=3Dblue face=3DArial><span = style=3D'font-size: 10.0pt;mso-bidi-font-size:12.0pt;font-family:Arial;color:blue'>Feral = Errol<o:p></o:p></span></font></p> <p class=3DMsoNormal><font size=3D2 color=3Dred face=3DArial><span = style=3D'font-size: 10.0pt;mso-bidi-font-size:12.0pt;font-family:Arial;color:red'>Get = Serious!</span></font><font size=3D2 color=3Dblue face=3DArial><span = style=3D'font-size:10.0pt;mso-bidi-font-size: 12.0pt;font-family:Arial;color:blue'> </span></font><font = color=3Dnavy><span style=3D'color:navy'><a = href=3D"http://www.datrats.com.au/";>http://www.datrats.com.au/</a></span >= </font><font color=3Dnavy><span = style=3D'color:navy;mso-color-alt:windowtext'><o:p></o:p></span></font>< /= p> <p class=3DMsoNormal><!--[if supportFields]><span = class=3DEmailStyle18><font=20 size=3D2 color=3Dnavy face=3DArial><span = style=3D'font-size:10.0pt;mso-bidi-font-size: 12.0pt;font-family:Arial'><span = style=3D'mso-element:field-end'></span></span></font></span><![endif]--> <= span class=3DEmailStyle18><font size=3D2 color=3Dnavy face=3DArial><span = style=3D'font-size: 10.0pt;mso-bidi-font-size:12.0pt;font-family:Arial'><![if = !supportEmptyParas]> <![endif]><o:p></o:p></span></font></span></p> <p class=3DMsoNormal style=3D'margin-left:36.0pt'><font size=3D2 = color=3Dblack face=3DTahoma><span = style=3D'font-size:10.0pt;font-family:Tahoma;color:black'>-----Original Message-----<br> <b><span style=3D'font-weight:bold'>From:</span></b> [EMAIL PROTECTED] = [mailto:[EMAIL PROTECTED]<b><span style=3D'font-weight:bold'>On Behalf Of </span></b>Jimmy<br> <b><span style=3D'font-weight:bold'>Sent:</span></b> Friday, March 19, = 2004 9:11 PM<br> <b><span style=3D'font-weight:bold'>To:</span></b> = [EMAIL PROTECTED]<br> <b><span style=3D'font-weight:bold'>Subject:</span></b> RE: Master = Cylinder</span></font></p> <p class=3DMsoNormal style=3D'margin-left:36.0pt'><font size=3D3 face=3D"Times New Roman"><span style=3D'font-size:12.0pt'><![if = !supportEmptyParas]> <![endif]><o:p></o:p></span></font></p> <p class=3DMsoNormal style=3D'margin-left:36.0pt'><font size=3D3 = color=3Dblack face=3D"Times New Roman"><span style=3D'font-size:12.0pt;color:black'>i = got a 1" and it weighs about twice the amount of the 7/8 cylinder. same = shape and size though. should be good for the 4spot skyline = brakes.</span></font><font color=3Dblack><span = style=3D'color:black;mso-color-alt:windowtext'><o:p></o:p></span></font> <= /p> <p class=3DMsoNormal style=3D'margin-left:36.0pt'><font size=3D3 = color=3Dblack face=3D"Times New Roman"><span = style=3D'font-size:12.0pt;color:black'><br> <br> <b><i><span style=3D'font-weight:bold;font-style:italic'>"Mohit K. Autar" <[EMAIL PROTECTED]></span></i></b> = wrote:</span></font><font color=3Dblack><span = style=3D'color:black;mso-color-alt:windowtext'><o:p></o:p></span></font> <= /p> <div style=3D'border:none;border-left:solid #1010FF 1.5pt;padding:0cm = 0cm 0cm 4.0pt'> <p class=3DMsoNormal = style=3D'margin-right:36.0pt;mso-margin-top-alt:auto; margin-bottom:12.0pt;margin-left:39.75pt;border:none;mso-border-left-alt := solid #1010FF 1.5pt; padding:0cm;mso-padding-alt:0cm 0cm 0cm 4.0pt'><font size=3D3 = color=3Dblack face=3D"Times New Roman"><span style=3D'font-size:12.0pt;color:black'>hi = there,<br> im also upgrading brakes on my datsun 1400 p.510.can anyone tell me what = to use.<br> <br> -----Original Message-----<br> From: Ben Holko [mailto:[EMAIL PROTECTED]<br> Sent: Wednesday, February 18, 2004 3:53 PM<br> To: [EMAIL PROTECTED]<br> Subject: Master Cylinder<br> <br> <br> Hey all,<br> <br> I'm in the middle of upgrading the brakes on the 180B SSS, and need = to<br> upgrade the master cylinder.<br> <br> I'll email details of exactly what I'm using for brakes once it's = finished,<br> but I am going to need at least a 1" master cylinder.<br> <br> Is there a 1" that will bolt straight on? The biggest I know of is = 7/8.<br> <br> Has anyone gone bigger than 7/8 on your 510/610, and if so what did you = use?<br> <br> thanks!<br> <br> Ben<br> <br> <br> <br> <br> --membersozdat-------------------------------------------------------<br >= OZDAT Mailing List Please Note:-<br> Send (un)subscribe requests to [EMAIL PROTECTED]<br> Send submissions to [EMAIL PROTECTED]<br> No unauthorised redistribution of this email<br> http://www.ozdat.com/ozdatonline/index.htm<br> http://www.ozdat.com/ozdatonline/listindex.html<br> http://www.mail-archive.com/[EMAIL PROTECTED]/<br> ---------------------------------------------------------------------Thi s= email and any files transmitted with it are confidential and intended solely = for<br> the use of the individual or entity to whom they are addressed. If you = have received<br> this mail in error, please notify the System Administrator. Please note = that any views <br> or opinions presented in this mail are solely those of the author and do = not necessarily<br> represent those of the Institute. Finally the recipient should check = this mail and any <br> attachment for the presence of viruses. FIT has a virus detection in = place and makes <br> every reasonable effort to ensure that this message is free f! rom = viruses. FIT accepts <br> no liability for any damage caused by any virus transmitted by this = mail</span></font><font color=3Dblack><span = style=3D'color:black;mso-color-alt:windowtext'><o:p></o:p></span></font> <= /p> </div> <p style=3D'margin-left:36.0pt'><font size=3D3 color=3Dblack = face=3D"Times New Roman"><span style=3D'font-size:12.0pt;color:black'><![if = !supportEmptyParas]> <![endif]></span></font><font color=3Dblack><span = style=3D'color:black;mso-color-alt:windowtext'><o:p></o:p></span></font> <= /p> <div class=3DMsoNormal align=3Dcenter = style=3D'margin-left:36.0pt;text-align:center'><font size=3D3 color=3Dblack face=3D"Times New Roman"><span = style=3D'font-size:12.0pt; color:black'> <hr size=3D1 width=3D"100%" align=3Dcenter> </span></font></div> <p class=3DMsoNormal style=3D'margin-left:36.0pt'><font size=3D3 = color=3Dblack face=3D"Times New Roman"><span = style=3D'font-size:12.0pt;color:black'>Find local movie times and trailers on <a href=3D"http://au.rd.yahoo.com/mail/tagline/*http://au.movies.yahoo.com"; target=3D"_blank"><b><span style=3D'font-weight:bold'>Yahoo! = Movies.</span></b></a><br> <br> --membersozdat------------------------------------------------------- = <br> OZDAT Mailing List Please Note:- <br> Send (un)subscribe requests to [EMAIL PROTECTED] <br> Send submissions to [EMAIL PROTECTED] <br> No unauthorised redistribution of this email <br> http://www.ozdat.com/ozdatonline/index.htm <br> http://www.ozdat.com/ozdatonline/listindex.html <br> http://www.mail-archive.com/[EMAIL PROTECTED]/ <br> ---------------------------------------------------------------------</s p= an></font><font color=3Dblack><span = style=3D'color:black;mso-color-alt:windowtext'><o:p></o:p></span></font> <= /p> </div> </body> </html> ------=_NextPart_000_0003_01C40E02.434D9D60-- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[EMAIL PROTECTED]/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[EMAIL PROTECTED]/ ---------------------------------------------------------------------
