Not sure about hot spaces, but in the wet PNW, if the dang paint failed in two years, the car was off to the dealer under warrantee. I had a few neighbors who had the chrysler POS paint and ended up with new paint on the car. The newer coating lasted more than a few years.
Though a black or dark car is pretty spiffy, in a warm environment, the lighter colors are more in vogue. Or at least they were when I lived in warm environments. A blue was more pastel, reds were .. well, red. Light green, orange, white, silver, all colors that would not suck up calories, which might scorch a kid should it touch it. AT that time, not too many cars were AC equipped, so interiors were light if not fabric. clay > On Sep 18, 2016, at 6:11 AM, Curley McLain via Mercedes > <mercedes@okiebenz.com> wrote: > > In the case of cars in hot places, do people get them repainted with a solid > color after a couple years, or just drive around with the clear peeling? > Probably, it depends. The old pickup does not get painted. But does the 2 > yr old car used for business? > > My only experience was with Livingston, CA and people there seemed to repaint > the cars and trucks in a solid white. But that was maybe 15 years ago when > clear was not as prevalent. Made sense to me, it you were going to live in a > hot place... > >> G Mann via Mercedes <mailto:mercedes@okiebenz.com> >> September 18, 2016 at 12:27 AM >> Clear coat paint is a programmed failure. Mechanically, sunlight passes >> through the clear coat, is reflected by the base coat, which is smooth and >> reflective under the clear coat.. when the UV light is refracted back to >> the surface of the clear coat, it is reflected back to the base coat, >> because the surface of the clear coat "on the surface" is cloudy and the UV >> light can't get out.. so it bounces back and forth, all the while >> microscopically super heating the clear coating, which caused it to >> separate from the base coat and fail... >> >> Bad system design... Looks nice for a couple years.. then fails >> progressively faster... By it's nature.. it "bonds" to the base coat.. so >> can't be stripped as an individual coating... >> >> In Arizona.. where clear coat failure only takes one year instead of two, >> because the sun shines 353 days of the year.. >> >> Grant... >> >> On Sat, Sep 17, 2016 at 10:05 PM, clay via Mercedes <mercedes@okiebenz.com> >> _______________________________________ >> http://www.okiebenz.com >> >> To search list archives http://www.okiebenz.com/archive/ >> >> To Unsubscribe or change delivery options go to: >> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com >> >> clay via Mercedes <mailto:mercedes@okiebenz.com> >> September 18, 2016 at 12:05 AM >> Gump had a massive case of clear coat Leprosy. I used a razor to cut away >> the really bad patches. I also did the sanding of edges to try to feather it >> in an attempt to get it to stop spreading. The stuff was resistant to my >> ministrations. I suspect there was a respray at one time and the coat was >> destined to fail. My suspicion would be that complete removal by sanding >> would give you a much better surface to begin with. Polei has a few spots of >> entrenched clear ( really small less than a folded dollar) that I sanded >> down the edges if I could not completely obliterate. I used 80 grit as a >> first phase, then went 100/150 then 220/320 before I did a 400/600 sanding, >> which ended with 800/1000 so that there were no hard edges or the stuff was >> gone. >> >> clay >> >> >> >> >> >> _______________________________________ >> http://www.okiebenz.com >> >> To search list archives http://www.okiebenz.com/archive/ >> >> To Unsubscribe or change delivery options go to: >> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com >> >> Dan Penoff via Mercedes <mailto:mercedes@okiebenz.com> >> September 17, 2016 at 6:39 PM >> I am going to look at a W126 tomorrow that has clear coat peeling on the >> roof. The rest of the car might be OK, so I’m trying to get a feel for what >> I might be getting into should I want to buy it. >> >> As an interim approach, can the edges of the clear coat be feathered and >> just polished or buffed out so it blends into the surface? >> >> I assume that clear coat could be reapplied to seal the area back up again? >> >> Any paint enabled folks here who want to comment or make recommendations >> would be appreciated. >> >> Dan >> _______________________________________ >> http://www.okiebenz.com >> >> To search list archives http://www.okiebenz.com/archive/ >> >> To Unsubscribe or change delivery options go to: >> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com >> > > _______________________________________ > http://www.okiebenz.com > > To search list archives http://www.okiebenz.com/archive/ > > To Unsubscribe or change delivery options go to: > http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com > _______________________________________ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com