<<mchev11.pcb>> I have 4 copies of this file in 4 different folders. The one attached is the only one that has the "Misc" option. It is in my \sm11\mill\quickstep folder.
Pete > -----Original Message----- > From: John Huston [SMTP:[EMAIL PROTECTED]] > Sent: Thursday, November 16, 2000 7:57 PM > To: [EMAIL PROTECTED] > Cc: 'Jon Baker'; 'Smartcam Users Group (E-mail)' > Subject: Re: [mfg-smartcam] Misc Stuff > > If I remember correctly (not a sure thing these days) you need to check > the > "Productivity Macros" in the "Installation Options" box. This will should > load: > > mchevnt=E:\SM11-5\MILL\QUIKSTEP\MCHEV11.PCB > options=E:\SM11-5\MILL\QUIKSTEP\QUIKSTP.PCB > > <john> > > Bob Looney wrote: > > > hmmm. I don't see it on a cd. Maybe it was on an old set of floppies > from V8 > > era?. I chucked my floppies so maybe somebody may have it. John G. at > SDRC > > will know about it, they are "SmartCAM productivity Macros". I can zip > the > > folder if you need it. > > bob > > > > -----Original Message----- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED]]On Behalf Of Jon Baker > > Sent: Thursday, November 16, 2000 3:42 PM > > To: 'Smartcam Users Group (E-mail)' > > Subject: Re: [mfg-smartcam] Misc Stuff > > > > Hey cool, I'm gonna have to spend more time looking over that CD, and > less > > time chasing porn on the internet. > > :o) > > Thanks Bob > > Jon > > ----- Original Message ----- > > From: "Bob Looney" <[EMAIL PROTECTED]> > > To: "'Jon Baker'" <[EMAIL PROTECTED]>; " 'Smartcam Users Group > (E-mail)'" > > <[EMAIL PROTECTED]> > > Sent: Thursday, November 16, 2000 3:05 PM > > Subject: RE: [mfg-smartcam] Misc Stuff > > > > > it's a non standard mchev11.pcb file in my sm11\quickstep folder. I > think > > > the quickstep executable is on the cd somewhere. > > > bob > > > > > > -----Original Message----- > > > From: [EMAIL PROTECTED] > > > [mailto:[EMAIL PROTECTED]]On Behalf Of Jon Baker > > > Sent: Thursday, November 16, 2000 2:39 PM > > > To: Smartcam Users Group (E-mail) > > > Subject: Re: [mfg-smartcam] Misc Stuff > > > > > > > > > Where did you get that. I just checked under freeform, and there is > no > > > "Misc. Options" Anybody know where this came from and better yet, how > I > > can > > > get it too? > > > Jon > > > > > > ----- Original Message ----- > > > From: "Mike Sharp" <[EMAIL PROTECTED]> > > > To: "Smartcam Users Group (E-mail)" <[EMAIL PROTECTED]> > > > Sent: Thursday, November 16, 2000 12:55 PM > > > Subject: [mfg-smartcam] Misc Stuff > > > > > > > > > > Hi everyone > > > > > > > > I am using PM11.5. Under Create, Machine Events, Misc Options There > is a > > > > panel with M00, M01, Block Delete and Message. How do I access this > info > > > in > > > > my template file? > > > > > > > > Thanks > > > > Mike > > > > > ====================================================================== > > > > To find out more about this mailing list including how to > unsubscribe, > > > > send the message "info mfg-smartcam" to [EMAIL PROTECTED] > > > > > ====================================================================== > > > > > > > > > > > > > > ====================================================================== > > > To find out more about this mailing list including how to unsubscribe, > > > send the message "info mfg-smartcam" to [EMAIL PROTECTED] > > > ====================================================================== > > > > > > ====================================================================== > To find out more about this mailing list including how to unsubscribe, > send the message "info mfg-smartcam" to [EMAIL PROTECTED] > ======================================================================
mchev11.pcb
Description: Binary data
