Hi,
I am testing out OpenBSD on a second laptop I have. I just swapped in a
HD I use on my ThinkPad.
For the test, I run a stock 5.2 kernel or a 5.3 with the "network" card
patch from Miod that Sebastian compiled for me.
I have two, possibly related problems:
- the fan runs always at full speed even with loads of 0.1 or 0.2
- no battery information is returned I get:
$ apm
Battery state: unknown, 0% remaining, 0 minutes life estimate
A/C adapter state: not connected
Performance adjustment mode: manual (599 MHz)
Interesting is that the CPU is not running at full speed, which is 1600Mhz.
I suppose this is part of the problem:
$ dmesg | grep acpi
acpi at bios0 function 0x0 not configured
Riccardo
PS: this is the full dmesg
OpenBSD 5.2 (GENERIC) #278: Wed Aug 1 10:04:16 MDT 2012
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) M processor 1.60GHz ("GenuineIntel" 686-class)
599 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,EST,TM2
real mem = 536211456 (511MB)
avail mem = 516587520 (492MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 06/23/05, BIOS32 rev. 0 @ 0xf0000,
SMBIOS rev. 2.3 @ 0xfa1ee (31 entries)
bios0: vendor Hewlett-Packard version "68BDD Ver. F.14" date 06/23/2005
bios0: Hewlett-Packard HP Compaq nc6000 (DU447EA#ABZ)
apm0 at bios0: Power Management spec V1.2 (BIOS managing devices)
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x2000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf0840/160 (8 entries)
pcibios0: bad IRQ table checksum
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf6360/160 (8 entries)
pcibios0: PCI Exclusive IRQs: 5 10 11
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801DBM LPC" rev 0x00)
pcibios0: PCI bus #5 is the last bus
bios0: ROM list: 0xc0000/0x10000
cpu0 at mainbus0: (uniprocessor)
cpu0: Enhanced SpeedStep 599 MHz: speeds: 1600, 1400, 1200, 1000, 800,
600 MHz
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82855PM Host" rev 0x03
intelagp0 at pchb0
agp0 at intelagp0: aperture at 0xb0000000, size 0x10000000
ppb0 at pci0 dev 1 function 0 "Intel 82855PM AGP" rev 0x03
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Radeon Mobility M10" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
radeondrm0 at vga1: irq 10
drm0 at radeondrm0
uhci0 at pci0 dev 29 function 0 "Intel 82801DB USB" rev 0x03: irq 10
uhci1 at pci0 dev 29 function 1 "Intel 82801DB USB" rev 0x03: irq 10
uhci2 at pci0 dev 29 function 2 "Intel 82801DB USB" rev 0x03: irq 10
ehci0 at pci0 dev 29 function 7 "Intel 82801DB USB" rev 0x03: irq 10
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb1 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x83
pci2 at ppb1 bus 2
ath0 at pci2 dev 4 function 0 "Atheros AR5212" rev 0x01: irq 11
ath0: AR5213 5.6 phy 4.1 rf5111 1.7 rf2111 2.3, WOR0W, address
00:12:79:3d:3d:9c
cbb0 at pci2 dev 6 function 0 "O2 Micro OZ711E0 CardBus" rev 0x00: irq 10
cbb1 at pci2 dev 6 function 1 "O2 Micro OZ711E0 CardBus" rev 0x00: irq 10
"O2 Micro OZ711Mx Misc" rev 0x00 at pci2 dev 6 function 2 not configured
cbb2 at pci2 dev 6 function 3 "O2 Micro OZ711E0 CardBus" rev 0x00: irq 10
bge0 at pci2 dev 14 function 0 "Broadcom BCM5705M Alt" rev 0x03, BCM5705
A3 (0x3003): irq 11, address 00:08:02:e9:14:06
brgphy0 at bge0 phy 1: BCM5705 10/100/1000baseT PHY, rev. 2
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 3 device 0 cacheline 0x0, lattimer 0x20
pcmcia0 at cardslot0
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 4 device 0 cacheline 0x0, lattimer 0x20
pcmcia1 at cardslot1
cardslot2 at cbb2 slot 2 flags 0
cardbus2 at cardslot2: bus 5 device 0 cacheline 0x0, lattimer 0x20
pcmcia2 at cardslot2
ichpcib0 at pci0 dev 31 function 0 "Intel 82801DBM LPC" rev 0x03: 24-bit
timer at 3579545Hz
pciide0 at pci0 dev 31 function 1 "Intel 82801DBM IDE" rev 0x03: DMA,
channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <IBM-DJSA-210>
wd0: 16-sector PIO, LBA, 5729MB, 11733120 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TEAC, DW-224E-A, A.2F> ATAPI 5/cdrom
removable
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2
auich0 at pci0 dev 31 function 5 "Intel 82801DB AC97" rev 0x03: irq 11,
ICH4 AC97
ac97: codec id 0x41445374 (Analog Devices AD1981B)
ac97: codec features headphone, 20 bit DAC, No 3D Stereo
audio0 at auich0
"Intel 82801DB Modem" rev 0x03 at pci0 dev 31 function 6 not configured
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com2 at isa0 port 0x3e8/8 irq 5: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
wsmouse1 at pms0 mux 0
pms0: Synaptics touchpad, firmware 5.9
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
mtrr: Pentium Pro MTRR support
uhidev0 at uhub1 port 2 configuration 1 interface 0 "Trust USB OPTICAL
MOUSE" rev 1.10/1.00 addr 2
uhidev0: iclass 3/1
ums0 at uhidev0: 3 buttons, Z dir
wsmouse2 at ums0 mux 0
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
root on wd0a (0e00445d79f00c64.a) swap on wd0b dump on wd0b
