Hello, I was hoping that my TP-Link TL-WN8200ND works in 5.4, but it looks like it is only detected as an unsupported USB device.
ugen0 at uhub0 port 2 "Realtek 802.11n WLAN Adapter" rev 2.00/2.00 addr 2 While the documentation from the provider is not verbose about the chipset used, the following page claims that it is a Realtek RTL8192CU, which seems to be supported by urtwn(4). http://wikidevi.com/wiki/TP-LINK_TL-WN8200ND Assuming that the firmware was missing, I tried fw_update, but that did not download any firmware files. I would be thankful for any kind of help to get this adapter running. Bernd # usbdevs -v Controller /dev/usb0: addr 1: high speed, self powered, config 1, EHCI root hub(0x0000), RDC(0x17f3), rev 1.00 port 1 powered port 2 addr 2: high speed, power 500 mA, config 1, 802.11n WLAN Adapter(0x0100), Realtek(0x2357), rev 2.00, iSerialNumber 00e04c000001 Controller /dev/usb1: addr 1: high speed, self powered, config 1, EHCI root hub(0x0000), RDC(0x17f3), rev 1.00 port 1 powered port 2 powered Controller /dev/usb2: addr 1: full speed, self powered, config 1, OHCI root hub(0x0000), RDC(0x17f3), rev 1.00 port 1 powered port 2 powered Controller /dev/usb3: addr 1: full speed, self powered, config 1, OHCI root hub(0x0000), RDC(0x17f3), rev 1.00 port 1 powered port 2 powered # dmesg OpenBSD 5.4 (GENERIC) #37: Tue Jul 30 12:05:01 MDT 2013 dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Vortex86 SoC (586-class) 934 MHz cpu0: FPU,TSC,CX8,MMX real mem = 1039724544 (991MB) avail mem = 1011290112 (964MB) mainbus0 at root bios0 at mainbus0: AT/286+ BIOS, date 11/26/10, BIOS32 rev. 0 @ 0xf0010 apm0 at bios0: Power Management spec V1.2 pcibios0 at bios0: rev 3.0 @ 0xf0000/0x10000 pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf2fe0/240 (13 entries) pcibios0: no compatible PCI ICU found: ICU vendor 0x17f3 product 0x6036 pcibios0: Warning, unable to fix up PCI interrupt routing pcibios0: PCI bus #0 is the last bus bios0: ROM list: 0xc0000/0x8000 cpu0 at mainbus0: (uniprocessor) pci0 at mainbus0 bus 0: configuration mode 1 (bios) pchb0 at pci0 dev 0 function 0 vendor "RDC", unknown product 0x6022 rev 0x00 rl0 at pci0 dev 1 function 0 "Realtek 8139" rev 0x10: irq 11, address 44:4d:50:07:1b:19 rlphy0 at rl0 phy 0: RTL internal PHY rl1 at pci0 dev 2 function 0 "Realtek 8139" rev 0x10: irq 11, address 44:4d:50:07:1b:1a rlphy1 at rl1 phy 0: RTL internal PHY pcib0 at pci0 dev 7 function 0 vendor "RDC", unknown product 0x6036 rev 0x00 vte0 at pci0 dev 8 function 0 "RDC R6040 Ethernet" rev 0x00: irq 6, address 00:1b:eb:25:30:9e rdcphy0 at vte0 phy 1: R6040 10/100 PHY, rev. 1 ohci0 at pci0 dev 10 function 0 "RDC R6060 USB" rev 0x12: irq 7, version 1.0, legacy support ehci0 at pci0 dev 10 function 1 "RDC R6061 USB" rev 0x03: irq 3 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 "RDC EHCI root hub" rev 2.00/1.00 addr 1 ohci1 at pci0 dev 11 function 0 "RDC R6060 USB" rev 0x12: irq 5, version 1.0, legacy support ehci1 at pci0 dev 11 function 1 "RDC R6061 USB" rev 0x03: irq 9 usb1 at ehci1: USB revision 2.0 uhub1 at usb1 "RDC EHCI root hub" rev 2.00/1.00 addr 1 pciide0 at pci0 dev 12 function 0 "RDC R1011 IDE" rev 0x01: DMA (unsupported), channel 0 configured to compatibility, channel 1 configured to compatibility pciide0: channel 0 ignored (not responding; disabled or no drives?) wd0 at pciide0 channel 1 drive 0: <ST9320421AS> wd0: 16-sector PIO, LBA48, 305245MB, 625142448 sectors vga1 at pci0 dev 13 function 0 vendor "RDC", unknown product 0x2012 rev 0x00 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) azalia0 at pci0 dev 14 function 0 vendor "RDC", unknown product 0x3010 rev 0x01: irq 10 azalia0: No codecs found isa0 at pcib0 isadma0 at isa0 com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo com0: probed fifo depth: 0 bytes pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pcppi0 at isa0 port 0x61 spkr0 at pcppi0 npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 usb2 at ohci0: USB revision 1.0 uhub2 at usb2 "RDC OHCI root hub" rev 1.00/1.00 addr 1 usb3 at ohci1: USB revision 1.0 uhub3 at usb3 "RDC OHCI root hub" rev 1.00/1.00 addr 1 ugen0 at uhub0 port 2 "Realtek 802.11n WLAN Adapter" rev 2.00/2.00 addr 2 vscsi0 at root scsibus0 at vscsi0: 256 targets softraid0 at root scsibus1 at softraid0: 256 targets root on wd0a (197b846eebaa6c90.a) swap on wd0b dump on wd0b