Am 03.02.2014 17:54, schrieb Kenneth Westerback:
Reactivating the dhclient-script is not going to happen.
I am interested in what you would see syntax in dhclient.conf looking like.
Would multi-path routing modifications to all routes be needed? How should this
be combined with supersede/default/append commands for the relevant
options? Would it apply to all members of each option, or route by
route?
If all else fails you can always use the ISC dhclient from ports to
gain access to a dhclient-script again.
.... Ken
On 31 January 2014 02:04, Holger Glaess <gla...@glaessixs.de> wrote:
Am 30.01.2014 13:10, schrieb Giancarlo Razzolini:
Em 29-01-2014 18:13, Holger Glaess escreveu:
hi
i try to setup and multipath configuration with 2 line provider
1 cable with dhcp(client)
1 with pppoe
just dynamic ips.
the pppoe config create well the new default route with -math
but dhclient dont.
[snip pppoe config]
inet 0.0.0.0 255.255.255.255 NONE \
pppoedev msk0 authproto pap \
authname 'bla@blub' authkey 'blub' up
dest 0.0.0.1
!/sbin/route add -mpath default -ifp pppoe0 0.0.0.1
[/snip pppoe config]
after a couple of days i found that the dhclient not use the
dhclient-script since 5.3 anymore.
so how can i setup the -math option at the dhclient config ?
or it is possible to add some lines in dhclient that he check the
sysctl and , if net.inet.ip.multipath=1 ,
he add the default route with ( for ) multipathing.
holger
Check if your dhcp server always gives you the same router ip address.
If so, you can tweak with your dhclient.conf to reject and not ask for
routers, and then set it up manually as you do in your hostname.pppoe0.
And you can always run a script that is run after the dhcp negotiation,
looks for the gateway related entry, deletes it and then re-adds it with
the mpath modifier. There are a lot of options in this regard.
Cheers,
hi
shure , i can write a wrap around solution for the but this not the
"dynamic" way like
pppoe or dhcp to get and set ips.
i'm not the C programmer but i think it is not mutch work to add a solution
in dhclient,
or as option to reaktivate the dhclient-script part.
holger
hi
at moment i have following setup
# cat hostname.pppoe0
inet 0.0.0.0 255.255.255.255 NONE \
pppoedev msk0 authproto pap \
authname 'bla' authkey 'blub' up
dest 0.0.0.1
#!/sbin/route add default -ifp pppoe0 0.0.0.1
#!/sbin/route add -inet6 default -ifp pppoe0 ::0.0.0.1
#
!/sbin/route add -mpath default -ifp pppoe0 0.0.0.1
!/sbin/route add -inet6 -mpath default -ifp pppoe0 ::0.0.0.1
# cat /etc/hostname.vlan5
dhcp vlandev msk1
!/sbin/route add -mpath default xww.x.yy.zz.
# cat /etc/dhclient.conf
timeout 15;
retry 5;
reboot 2;
select-timeout 5;
initial-interval 2;
interface "vlan5" {
ignore domain-name-servers;
ignore host-name;
ignore routers;
send dhcp-lease-time 3600;
request subnet-mask, broadcast-address, time-offset, routers,
domain-name-servers, host-name, ntp-servers;
}
it work for a while with the mpath settings after the start but if the
dhclient renew his setting he set the default route
i his standard way , hi ignore the settings in his config ( is this
right ? )
holger
