Hi
Just installed 6.1-beta from snapshot Mar 14 on Edgerouter Lite 3 with
original U-Boot.
Loaded bootcmd 'usb reset; fatload usb 0 $loadaddr bsd; bootoctlinux
rootdev=sd0 coremask=0x3'
1. Installation just went through with the new installion routine as
described in INSTALL.octeon. Many thanks!
2. Used Snapshot OpenBSD 6.1-beta (GENERIC) #0: Tue Mar 14 21:24:42 UTC
2017
screen during boot showed me those errors:
...
/dev/ksyms: Symbol table not valid.
savecore: /bsd: kvm_read: version misread
kvm_mkdb: can't open /dev/ksyms
...
full dmesg below
Does this happen because of U-Boot ksyms(4) because of bug in mmap(2)?
3. I set coremask=0x3 to boot mp, in dmseg only 1 cpu is shown, but its
a dual core.
Tried with a changed bootcmd to bsd.mp
bootcmd 'usb reset; fatload usb 0 $loadaddr bsd.mp; bootoctlinux
rootdev=sd0 coremask=0x3'
No success for second core shown. Switched back to bsd, that works.
-oliver
-- dmesg ----
OpenBSD 6.1-beta (GENERIC) #0: Tue Mar 14 21:24:42 UTC 2017
visa@octeon:/usr/src/sys/arch/octeon/compile/GENERIC
real mem = 536870912 (512MB)
avail mem = 524238848 (499MB)
warning: no entropy supplied by boot loader
mainbus0 at root
cpu0 at mainbus0: CN50xx CPU rev 0.1 500 MHz, Software FP emulation
cpu0: cache L1-I 32KB 4 way D 8KB 64 way, L2 128KB 8 way
clock0 at mainbus0: int 5
iobus0 at mainbus0
dwctwo0 at iobus0 base 0x1180068000000 irq 56
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Octeon DWC2 root hub" rev
2.00/1.00 addr 1
octrng0 at iobus0 base 0x1400000000000 irq 0
cn30xxgmx0 at iobus0 base 0x1180008000000
cnmac0 at cn30xxgmx0: RGMII, address 04:18:d6:83:1c:5d
atphy0 at cnmac0 phy 7: AR8035 10/100/1000 PHY, rev. 2
cnmac1 at cn30xxgmx0: RGMII, address 04:18:d6:83:1c:5e
atphy1 at cnmac1 phy 6: AR8035 10/100/1000 PHY, rev. 2
cnmac2 at cn30xxgmx0: RGMII, address 04:18:d6:83:1c:5f
atphy2 at cnmac2 phy 5: AR8035 10/100/1000 PHY, rev. 2
uartbus0 at mainbus0
com0 at uartbus0 base 0x1180000000800 irq 34: ns16550a, 64 byte fifo
com0: console
com1 at uartbus0 base 0x1180000000c00 irq 35: ns16550a, 64 byte fifo
/dev/ksyms: Symbol table not valid.
umass0 at uhub0 port 1 configuration 1 interface 0 "SanDisk Cruzer Fit"
rev 2.10/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SanDisk, Cruzer Fit, 1.00> SCSI4 0/direct
removable serial.07815571271129122290
sd0: 15264MB, 512 bytes/sector, 31260672 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
boot device: sd0
root on sd0a (59b18176ad90ac10.a) swap on sd0b dump on sd0b
WARNING: No TOD clock, believing file system.
WARNING: CHECK AND RESET THE DATE!
