Hi Mark, viq, did either of you get it to work with the virtual table?
Mine mostly works with:
action "lmtp-local" mda "/usr/libexec/mail.lmtp -d
unix:/var/dovecot/lmtp -f %{sender} %{rcpt}" virtual <virtuals>
but it ignores the virtual table completely.
If I miss out the ${rcpt}, I get a no recipient specified and if I have
the {user.username} it gives a similar error.
Did your virtual<vusers> work or am I doing something daft?
Regards - Nick
On 27/05/2018 08:51, viq wrote:
On 18-05-27 09:34:10, Mark Patruck wrote:
For me it works with %{user.username} as mail.lmtp(8) user.
See "FORMAT SPECIFIERS" in smtpd.conf(5) for details.
Shows how well I read the man page.... With this it works, thank you!
On Sun, May 27, 2018 at 09:04:56AM +0200, viq wrote:
> On 18-05-26 19:18:56, Edgar Pettijohn III wrote:
> >
> > > Sorry, I've read the announcements, looked at man pages and examples,
> > > but still didn't manage to figure out how to translate "deliver via
dovecot
> > > lmtp"
> > > (to have sieve working) into the new syntax. So far my config was:
> > >
> > > table vusers ldap:/etc/mail/ldap.conf
> > > table vdomains ldap:/etc/mail/ldap.conf
> > > table passwd ldap:/etc/mail/ldap.conf
> > >
> > > accept from local for local virtual <vusers> deliver to lmtp
> > > "/var/dovecot/lmtp"
> > > accept from any for domain <vdomains> virtual <vusers> deliver to lmtp
> > > "/var/dovecot/lmtp"
> > >
> > >
> > > I tried changing those into:
> > >
> > > action "lmtp-local" mda "/usr/libexec/mail.lmtp -d /var/dovecot/lmtp"
> >
> > try:
> > action "lmtp-local" mda "/usr/libexec/mail.lmtp -d unix:/var/dovecot/lmtp -f
> > %{sender}"
>
> Well, this time I'm getting
> result=TempFail stat=Error ("mail.lmtp: no recipient was specified")
> so there's difference. So I tried
> action "lmtp-local" mda "/usr/libexec/mail.lmtp -d unix:/var/dovecot/lmtp -f %{sender}
%{recipient}" virtual <vusers>
> but that resulted in
> result=TempFail stat=Error ("smtpd: mda command line could not be expanded:
Interrupted system call")
> same with %{rcpt-to}
>
> Where did you get the %{} syntax? I haven't seen it anywhere when
> reading about this.
>
> > However, this does feel odd. I need to switch over as well, but still trying
> > to wrap my brain around the new config.
> > > virtual <vusers>
> > > action "relay" relay
> > > match from local for local action "lmtp-local"
> > > match from any for domain <vdomains> action "lmtp-local"
> > > match from local for any action "relay"
> > >
> > >
> > > but delivery attempts fail with Error ("mail.lmtp: sender must be
specified
> > > with -f")
> > >
> > > What would be the proper config for this?
> > > --
> > > viq
> >
>
--
Mark Patruck ( mark at wrapped.cx )
GPG key 0xF2865E51 / 187F F6D3 EE04 1DCE 1C74 F644 0D3C F66F F286
5E51
http://www.wrapped.cx