I updated my -current version today, and found that the skeletal 3D animation runs very fine. Of course, any other models run fine, too. Thank you developpers to update drm drivers of amdgpu!
It still has sometime to freeze the move (yes, about 30 seconds) when I do something like stop the motion etc,, however, I cannot confirm the precise condition of it yet... Kenji 2018年12月19日(水) 15:49 岡本健二 <keokn...@gmail.com>: > I made FreeBSD 12-Release on another disk of the same graphic (HD 6450 > graphic card), > and got success to run Jahshaka 3D animation. Yes, no animation stop! > It uses mesa-18.1.9. > Its colors are not so good as OpenBSD's mesa version, however, it works. > > Kenji > > > 2018年12月11日(火) 13:14 岡本健二 <keokn...@gmail.com>: > >> Ok, I upgraded my OpenBSD system to -current, and rebuild the Jahshaka. >> After all, the results are same as before. >> >> Skeletal Animations runs for less than 1 second, and halt for about 35 >> seconds, >> and then runs for less than 1 second, and halt for about 35 second(yes, >> it's same)... >> Above cycle continues eternally. >> >> Kenji >> >> >> 2018年12月10日(月) 1:23 tfrohw...@fastmail.com <tfrohw...@fastmail.com>: >> >>> On December 9, 2018 1:22:42 AM UTC, "岡本健二" <keokn...@gmail.com> wrote: >>> >I found mesa-libs-18.1.9 for FreeBSD ports. >>> >How can I get it without FreeBSD system? >>> > >>> >Kenji >>> > >>> > >>> >2018年12月8日(土) 14:48 岡本健二 <keokn...@gmail.com>: >>> > >>> >> I installed Ubuntu 18.04 to a AMD 6450 graphic card, and played >>> >> Jahshaka. It has mesa version 18.2, and runs Jahshaka very >>> >> smoothly. >>> >> >>> >> The colors I reported before are same in this machine, so that >>> >> report was not correct. >>> >> >>> >> Kenji >>> >> >>> >> 2018年12月7日(金) 11:09 岡本健二 <keokn...@gmail.com>: >>> >> >>> >>> I checked mesa-18.3.0 sources under src/gallium/drivers/r600 and >>> >compared >>> >>> with those >>> >>> of xenocara. File names are all same, however, individual sizes are >>> >very >>> >>> different for >>> >>> most of those, which would not permit me to copy those to >>> >xenocara... >>> >>> >>> >>> Kenji >>> >>> >>> >>> >>> >>> 2018年12月6日(木) 15:14 岡本健二 <keokn...@gmail.com>: >>> >>> >>> >>>> also, it stull has some bugs, because the colors of some >>> >>>> parts are different from those of original ones. >>> >>>> >>> >>>> Kenji >>> >>>> >>> >>>> >>> >>>> 2018年12月6日(木) 15:10 岡本健二 <keokn...@gmail.com>: >>> >>>> >>> >>>>> Sorry, I'm a novice to OpenBSD. >>> >>>>> Yes, it's current branch of xenocara. >>> >>>>> I updated my xenocara (stable) to that current, and build new >>> >xenocara >>> >>>>> here. >>> >>>>> >>> >>>>> Wow, it makes the Jahshaka works! >>> >>>>> >>> >>>>> However, it still has some bugs, because it moves and stop >>> >suddenly and >>> >>>>> then >>> >>>>> move again. Whine the animation stops, the system seems to >>> >halting... >>> >>>>> >>> >>>>> Anyway it makes much advance, I included the screenshot of it. >>> >>>>> >>> >>>>> Kenji >>> >>>>> >>> >>>>> PS: sorry tfrohwein, this is doubled to you >>> >>>>> >>> >>>>> 2018年12月6日(木) 13:26 岡本健二 <keokn...@gmail.com>: >>> >>>>> >>> >>>>>> in-current means stable 6.4? >>> >>>>>> >>> >>>>>> Kenji >>> >>>>>> >>> >>>>>> 2018年12月5日(水) 23:58 tfrohw...@fastmail.com >>> ><tfrohw...@fastmail.com>: >>> >>>>>> >>> >>>>>>> On December 5, 2018 9:41:44 AM UTC, "岡本健二" <keokn...@gmail.com> >>> >>>>>>> wrote: >>> >>>>>>> >This errors come from >>> >>>>>>> >>> >>/usr/xenocara/lib/mesa/src/gallium/drivers/r600/r600_state_common.c. >>> >>>>>>> >The mesa version of OpenBSD6.4 is 13.0.6. >>> >>>>>>> >I'm running this Jahshaka on Ubutu 18.04, where the mesa >>> >version is >>> >>>>>>> >18.x. >>> >>>>>>> > >>> >>>>>>> >So, it may be the mesa problem... >>> >>>>>>> > >>> >>>>>>> >Kenji >>> >>>>>>> > >>> >>>>>>> > >>> >>>>>>> >2018年12月4日(火) 16:19 岡本健二 <keokn...@gmail.com>: >>> >>>>>>> > >>> >>>>>>> >> I'm using AMD HD6450 graphic card which I reported before, >>> >and >>> >>>>>>> faced >>> >>>>>>> >a >>> >>>>>>> >> curious thing >>> >>>>>>> >> during running Jahshaka Studio (dev version 7.03a). >>> >>>>>>> >> To run Jahshaka on OpenBSD 6.4 I needed to delete google >>> >breakpad >>> >>>>>>> >> temporally, which >>> >>>>>>> >> is not the problem now. >>> >>>>>>> >> >>> >>>>>>> >> After start to run 'Jahshaka Studio', I got start 3D >>> >animation >>> >>>>>>> sample >>> >>>>>>> >> 'Skeletal Animation' data to load, then >>> >>>>>>> >> I got many errors included below which seems to come from >>> >radeon >>> >>>>>>> drm >>> >>>>>>> >> driver's bug to me. >>> >>>>>>> >> If you interested please check it. >>> >>>>>>> >> >>> >>>>>>> >> Thanks in advance >>> >>>>>>> >> >>> >>>>>>> >> Kenji >>> >>>>>>> >> >>> >>>>>>> >> >>> >>>>>>> >>> >>>>>>> There's a known bug where the shader on r600 uses too many >>> >registers: >>> >>>>>>> >>> >>>>>>> https://bugs.freedesktop.org/show_bug.cgi?id=99349 >>> >>>>>>> >>> >>>>>>> I encountered this bug with godot on a Radeon HD 7570, too, and >>> >it >>> >>>>>>> went away with the updated mesa that's in -current. >>> >>>>>>> >>> >>>>>> >>> >>> I think you are asking for way more than you (or most misc@ readers) >>> can handle. Porting low-level libraries from FreeBSD is far from trivial. >>> >>> My advice remains: if you want working graphics, you should run >>> OpenBSD-current, not 6.4-release. What you did is try to plug in stuff from >>> -current into 6.4 which is huge gamble and I'm not surprised if the result >>> is weird. >>> >>> Just read the OpenBSD FAQ again for how to install -current. I would >>> stop experimenting like you've one until you understand the system much >>> better than now. >>> >>
