maybe no need to ruin the 6.8 release with a mention of linux,"other unfinished broken operating systems" might be better as a reference point? :)
Sent with ProtonMail Secure Email. ‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐ On Sunday, 18 October 2020 18:02, stolen data <stolen.data....@gmail.com> wrote: > 6.8 seems to work OK on the Arm64 Pine A64+ with 1GB RAM. > > Some observations: > > OpenBSD sees 896MB of RAM and makes only 838MB available. When running > Debian Linux on the exact same board the available RAM after boot is > 994MB, a difference of more than 150MB. Perhaps this can be improved by > tuning the DTB. > > A contrived test of network performance, using httpd(8) to serve a > large file from an mfs ramdisk over plain http, yields about 175 mbit/s > sustained transfer speed. I was not expecting to reach even 100 mbit/s > so this was a positive surprise, even if it's nowhere near the full > gigabit that other OSes can squeeze out of this board. > > ================================================================================================================================================================================================================================================================================================================================================================================================================================================================================================================================================================================================================================================================= > > OpenBSD 6.8 (GENERIC.MP) #828: Sun Oct 4 20:35:47 MDT 2020 > dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/GENERIC.MP > real mem = 940503040 (896MB) > avail mem = 879267840 (838MB) > random: good seed from bootblocks > mainbus0 at root: Pine64+ > psci0 at mainbus0: PSCI 1.1, SMCCC 1.2 > cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4 > cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache > cpu0: 512KB 64b/line 16-way L2 cache > cpu1 at mainbus0 mpidr 1: ARM Cortex-A53 r0p4 > cpu1: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache > cpu1: 512KB 64b/line 16-way L2 cache > cpu2 at mainbus0 mpidr 2: ARM Cortex-A53 r0p4 > cpu2: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache > cpu2: 512KB 64b/line 16-way L2 cache > cpu3 at mainbus0 mpidr 3: ARM Cortex-A53 r0p4 > cpu3: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache > cpu3: 512KB 64b/line 16-way L2 cache > efi0 at mainbus0: UEFI 2.8 > efi0: Das U-Boot rev 0x20200700 > apm0 at mainbus0 > "display-engine" at mainbus0 not configured > "osc24M_clk" at mainbus0 not configured > "osc32k_clk" at mainbus0 not configured > "internal-osc-clk" at mainbus0 not configured > simpleaudio0 at mainbus0 > "spdif-out" at mainbus0 not configured > agtimer0 at mainbus0: tick rate 24000 KHz > simplebus0 at mainbus0: "soc" > sxisyscon0 at simplebus0 > sxisid0 at simplebus0 > sxiccmu0 at simplebus0 > sxipio0 at simplebus0: 103 pins > ampintc0 at simplebus0 nirq 224, ncpu 4 ipi: 0, 1: "interrupt-controller" > sxirtc0 at simplebus0 > sxiccmu1 at simplebus0 > sxipio1 at simplebus0: 13 pins > sxirsb0 at simplebus0 > axppmic0 at sxirsb0 addr 0x3a3: AXP803 > "de2" at simplebus0 not configured > "dma-controller" at simplebus0 not configured > "lcd-controller" at simplebus0 not configured > "lcd-controller" at simplebus0 not configured > sximmc0 at simplebus0 > sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma > "usb" at simplebus0 not configured > "phy" at simplebus0 not configured > ehci0 at simplebus0 > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev > 2.00/1.00 addr 1 > ohci0 at simplebus0: version 1.0 > ehci1 at simplebus0 > usb1 at ehci1: USB revision 2.0 > uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev > 2.00/1.00 addr 1 > ohci1 at simplebus0: version 1.0 > com0 at simplebus0sxiccmu_ccu_reset: 0x0000002e > : ns16550, no working fifo > com0: console > sxitwi0 at simplebus0 > iic0 at sxitwi0 > dwxe0 at simplebus0: address 02:ba:06:9f:01:af > rgephy0 at dwxe0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5 > "hdmi" at simplebus0 not configured > "hdmi-phy" at simplebus0 not configured > "interrupt-controller" at simplebus0 not configured > sxidog0 at simplebus0 > gpio0 at sxipio0: 32 pins > gpio1 at sxipio0: 32 pins > gpio2 at sxipio0: 32 pins > gpio3 at sxipio0: 32 pins > gpio4 at sxipio0: 32 pins > gpio5 at sxipio0: 32 pins > gpio6 at sxipio0: 32 pins > gpio7 at sxipio0: 32 pins > gpio8 at sxipio1: 32 pins > usb2 at ohci0: USB revision 1.0 > uhub2 at usb2 configuration 1 interface 0 "Generic OHCI root hub" rev > 1.00/1.00 addr 1 > usb3 at ohci1: USB revision 1.0 > uhub3 at usb3 configuration 1 interface 0 "Generic OHCI root hub" rev > 1.00/1.00 addr 1 > "hdmi-connector" at mainbus0 not configured > "binman" at mainbus0 not configured > scsibus0 at sdmmc0: 2 targets, initiator 0 > sd0 at scsibus0 targ 1 lun 0: <SD/MMC, 00000, 0000> removable > > sd0: 7620MB, 512 bytes/sector, 15605760 sectors > vscsi0 at root > scsibus1 at vscsi0: 256 targets > softraid0 at root > scsibus2 at softraid0: 256 targets > bootfile: sd0a:/bsd > boot device: sd0 > root on sd0a (e07784d42ee158ca.a) swap on sd0b dump on sd0b > > =====================================================================================================================================================================================================================================================
