This is current/i386 on an ALIX.1E (dmesg below).
I am trying to monitor the CPU temperature with
wbsio0 at isa0 port 0x2e/2: W83627HF rev 0x41
lm1 at wbsio0 port 0x290/8: W83627HF
$ sysctl hw.sensors.lm1
hw.sensors.lm1.temp0=69.00 degC
hw.sensors.lm1.temp1=57.00 degC
hw.sensors.lm1.temp2=49.00 degC
hw.sensors.lm1.volt0=1.26 VDC (VCore A)
hw.sensors.lm1.volt1=2.64 VDC (VCore B)
hw.sensors.lm1.volt2=3.42 VDC (+3.3V)
hw.sensors.lm1.volt3=5.11 VDC (+5V)
hw.sensors.lm1.volt4=0.00 VDC (+12V)
hw.sensors.lm1.volt5=-14.91 VDC (-12V)
hw.sensors.lm1.volt6=-7.71 VDC (-5V)
hw.sensors.lm1.volt7=5.07 VDC (5VSB)
hw.sensors.lm1.volt8=0.00 VDC (VBAT)
There are three temperatures reported,
and dev/ic/lm78var.h talks about Temperature 1, 2, 3;
but man lm(4) only says
Temp uK Motherboard Temperature
Does anyone know what exactly they are?
Jan
OpenBSD 7.0-current (GENERIC) #276: Wed Nov 10 11:36:02 MST 2021
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
real mem = 259207168 (247MB)
avail mem = 238137344 (227MB)
random: good seed from bootblocks
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: date 07/19/10, BIOS32 rev. 0 @ 0xfa950
apm0 at bios0: Power Management spec V1.2 (slowidle)
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdfb4
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf30/128 (6 entries)
pcibios0: PCI Exclusive IRQs: 5 10 11
pcibios0: no compatible PCI ICU found: ICU vendor 0x1022 product 0x2090
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0xa800 0xef000/0x1000!
cpu0 at mainbus0: (uniprocessor)
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 499
MHz, 05-0a-02
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW
mtrr: K6-family MTRR support (2 registers)
amdmsr0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x33
vga1 at pci0 dev 1 function 1 "AMD Geode LX Video" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 13 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, address
00:0d:b9:0e:9e:f4
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
glxpcib0 at pci0 dev 15 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit
3579545Hz timer, watchdog, gpio, i2c
gpio0 at glxpcib0: 32 pins
iic0 at glxpcib0
pciide0 at pci0 dev 15 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SDCFHS-016G>
wd0: 1-sector PIO, LBA48, 15279MB, 31293360 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
auglx0 at pci0 dev 15 function 3 "AMD CS5536 Audio" rev 0x01: irq 11, CS5536
AC97
ac97: codec id 0x414c4770 (Avance Logic ALC203 rev 0)
ac97: codec features headphone, 20 bit DAC, 18 bit ADC, No 3D Stereo
audio0 at auglx0
ohci0 at pci0 dev 15 function 4 "AMD CS5536 USB" rev 0x02: irq 5, version 1.0,
legacy support
ehci0 at pci0 dev 15 function 5 "AMD CS5536 USB" rev 0x02: irq 5
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "AMD EHCI root hub" rev 2.00/1.00
addr 1
isa0 at glxpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
wbsio0 at isa0 port 0x2e/2: W83627HF rev 0x41
lm1 at wbsio0 port 0x290/8: W83627HF
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 configuration 1 interface 0 "AMD OHCI root hub" rev 1.00/1.00
addr 1
dt: 445 probes
umass0 at uhub0 port 4 configuration 1 interface 0 "JMicron USB to ATA/ATAPI
bridge" rev 2.00/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <CT240BX2, 00SSD1, MU02>
serial.152d2329801130168383
sd0: 228936MB, 512 bytes/sector, 468862128 sectors
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on wd0a (cfeae50a002d1e1d.a) swap on wd0b dump on wd0b
