On 5/4/06, Samurai Chef <[EMAIL PROTECTED]> wrote:
Use the LSI Logic SCSI controller.  That should help with getting it installed.



That worked! Thank you :-)

On 5/4/06, Murali Raju <[EMAIL PROTECTED]> wrote:
> Still no Virtual SMP support for *BSD on ESX. Are running 2.5.3? I
> can't seem to even get a normal OpenBSD install on ESX.
>
> Cheers..
>
> _Raju
>
> On 5/4/06, Craig Barraclough <[EMAIL PROTECTED]> wrote:
> > Just thought I'd check it out again, to see if it MP under VMware now 
works, unfortunately no.
> > dmesg below is from bsd, not bsd.mp unfortunately.
> >
> > (Following is hand copied, 'cause I still haven't worked out how to serial 
console a vmware machine).
> >
> > cpu1 failed to become ready
> > Stopped at      Debugger+0x4:      leave
> > ddb{0}> ps
> >    PID   PPID   PGRP       UID     S            FLAGS   WAIT             
COMMAND
> >      9      0      0         0     2         0x100204                    
crypto
> >      8      0      0         0     2         0x100204                    
aiodoned
> >      7      0      0         0     2         0x100204                    
update
> >      6      0      0         0     2         0x100204                    
cleaner
> >      5      0      0         0     2         0x100204                    
reaper
> >      4      0      0         0     2         0x100204                    
pagedaemon
> >      3      0      0         0     2        0x2100604                    
pfpurge
> >      2      0      0         0     3        0x2100204  kmalloc           
kmthread
> >      1      0      0         0     3        0x2000004  initexec          
swapper
> > *    0     -1      0         0     7        0x2080204                    
swapper
> > ddb{0}> trace
> > Debugger(d069b999, d0a98c14, 2c0, 0) at Debugger+0x4
> > cpu_boot_secondary(d0a98c00, 11, d05fcc12, d0828f70) at 
cpu_boot_secondary+0x99
> > cpu_boot_secondary_processors(4458a4a7, 0, 0, d05fcc12, 0) at 
cpu_boot_secondary_processors+0x41
> > main(0, 0, 0, 0, 0) at main+0x70c
> > ddb{0}> show registers
> > ds                  0x10
> > es                  0x10
> > fs                  0x58
> > gs                     0
> > edi             0x831000
> > esi           0xd0a98c00        end+0x2f18b0
> > ebp           0xd0828f18        end+0x81bc8
> > ebx                    0
> > edx                    0
> > ecx           0xd06bbb84        kprintf_mutex
> > eax                 0x1c
> > eip           0xd0448de0        Debugger+0x4
> > cs                   0x8
> > eflags             0x246
> > esp           0xd0828f18        end+0x81bc8
> > ss            0xd0820010        end+0x78cc0
> > Debugger+0x4:   leave
> > ddb{0}> boot dump
> >
> > -------
> > OpenBSD 3.9-current (GENERIC) #1: Wed May  3 13:58:50 EST 2006
> >     [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
> > cpu0: Intel Pentium II Xeon ("GenuineIntel" 686-class, 1024KB L2 cache) 450 
MHz
> > cpu0: 
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR
> > real mem  = 66613248 (65052K)
> > avail mem = 53035008 (51792K)
> > using 838 buffers containing 3432448 bytes (3352K) of memory
> > mainbus0 (root)
> > bios0 at mainbus0: AT/286+(2c) BIOS, date 04/21/04, BIOS32 rev. 0 @ 0xfd880
> > apm0 at bios0: Power Management spec V1.2
> > apm0: AC on, battery charge unknown
> > apm0: flags 30102 dobusy 0 doidle 1
> > pcibios0 at bios0: rev 2.1 @ 0xfd880/0x780
> > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf30/176 (9 entries)
> > pcibios0: PCI Interrupt Router at 000:07:0 ("Intel 82371FB ISA" rev 0x00)
> > pcibios0: PCI bus #1 is the last bus
> > bios0: ROM list: 0xc0000/0x8000 0xc8000/0x1a00! 0xca000/0x1000 
0xdc000/0x4000! 0xe4000/0x4000!
> > cpu0 at mainbus0
> > pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> > pchb0 at pci0 dev 0 function 0 "Intel 82443BX AGP" rev 0x01
> > ppb0 at pci0 dev 1 function 0 "Intel 82443BX AGP" rev 0x01
> > pci1 at ppb0 bus 1
> > pcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x08
> > pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel 
0 configured to compatibility, channel 1 configured to compatibility
> > atapiscsi0 at pciide0 channel 0 drive 0
> > scsibus0 at atapiscsi0: 2 targets
> > cd0 at scsibus0 targ 0 lun 0: <NECVMWar, VMware IDE CDR00, 1.00> SCSI0 
5/cdrom removable
> > cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
> > pciide0: channel 1 ignored (disabled)
> > piixpm0 at pci0 dev 7 function 3 "Intel 82371AB Power" rev 0x08: SMBus 
disabled
> > vga1 at pci0 dev 15 function 0 "VMware Virtual SVGA II" rev 0x00
> > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> > wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> > mpt0 at pci0 dev 16 function 0 "Symbios Logic 53c1030" rev 0x01: irq 9
> > scsibus1 at mpt0: 16 targets
> > sd0 at scsibus1 targ 0 lun 0: <VMware, Virtual disk, 1.0> SCSI2 0/direct 
fixed
> > sd0: 4096MB, 4096 cyl, 64 head, 32 sec, 512 bytes/sec, 8388608 sec total
> > sd1 at scsibus1 targ 1 lun 0: <VMware, Virtual disk, 1.0> SCSI2 0/direct 
fixed
> > sd1: 8192MB, 8192 cyl, 64 head, 32 sec, 512 bytes/sec, 16777216 sec total
> > mpt0: target 0 Synchronous at 160MHz width 16bit offset 127 QAS 1 DT 1 IU 1
> > mpt0: target 1 Synchronous at 160MHz width 16bit offset 127 QAS 1 DT 1 IU 1
> > pcn0 at pci0 dev 17 function 0 "AMD 79c970 PCnet-PCI" rev 0x10, Am79c970A, 
rev 0: irq 11, address 00:50:56:9c:20:ca
> > isa0 at pcib0
> > isadma0 at isa0
> > pckbc0 at isa0 port 0x60/5
> > pckbd0 at pckbc0 (kbd slot)
> > pckbc0: using irq 1 for kbd slot
> > wskbd0 at pckbd0: console keyboard, using wsdisplay0
> > pmsi0 at pckbc0 (aux slot)
> > pckbc0: using irq 12 for aux slot
> > wsmouse0 at pmsi0 mux 0
> > pcppi0 at isa0 port 0x61
> > midi0 at pcppi0: <PC speaker>
> > spkr0 at pcppi0
> > lpt0 at isa0 port 0x378/4 irq 7
> > npx0 at isa0 port 0xf0/16: using exception 16
> > pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
> > biomask e765 netmask ef65 ttymask ffe7
> > pctr: 686-class user-level performance counters enabled
> > mtrr: CPU supports MTRRs but not enabled
> > dkcsum: sd0 matches BIOS drive 0x80
> > dkcsum: sd1 matches BIOS drive 0x81
> > root on sd0a
> > rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
> > --
> > Craig
> >
> >
>
>
> --
> May the packets be with you.
>
>



--
May the packets be with you.

Reply via email to