I have a Tecra 520CDT laptop. This has one internal hard drive, and I'd like
to expand it by using a USB2 drive. The laptop has a single USB1 port, so
I've
acquired a generic Cardbus USB2/Firewire card.
This nearly works fine, but the EHCI part of the card is failing to start.
Luckily, due to various bits of good design it's gracefully falling back to
USB1, so I can access the drive, but it's, um, not fast.
Any suggestions? dmesg enclosed.
---
OpenBSD 4.0-stable (GENERIC) #0: Sun Mar 18 17:09:20 GMT 2007
[EMAIL PROTECTED]:/vol/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium/MMX ("GenuineIntel" 586-class) 166 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,MMX
cpu0: F00F bug workaround installed
real mem = 50032640 (48860K)
avail mem = 37126144 (36256K)
using 636 buffers containing 2605056 bytes (2544K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(63) BIOS, date 11/01/99, BIOS32 rev. 0 @ 0xfe95b
apm0 at bios0: Power Management spec V1.2
apm0: battery life expectancy 98%
apm0: AC on, battery charge high, charging, estimated 1:44 hours
apm0: flags 20102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf9980/80 (3 entries)
pcibios0: no compatible PCI ICU found: ICU vendor 0xffff product 0xffff
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #21 is the last bus
WARNING: can't reserve area for I/O APIC.
WARNING: can't reserve area for Local APIC.
bios0: ROM list: 0xe4000/0x9800
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Toshiba PCI" rev 0x26
cbb0 at pci0 dev 2 function 0 "Toshiba ToPIC95B CardBus" rev 0x07: irq 11
cbb1 at pci0 dev 2 function 1 "Toshiba ToPIC95B CardBus" rev 0x07: irq 11
vga1 at pci0 dev 4 function 0 "Chips and Technologies 65555" rev 0xc3
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ohci0 at pci0 dev 11 function 0 "NEC USB" rev 0x01: irq 11, version 1.0
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: NEC OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 20 device 0 cacheline 0x0, lattimer 0x0
pcmcia0 at cardslot0
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 21 device 0 cacheline 0x0, lattimer 0x0
pcmcia1 at cardslot1
isa0 at mainbus0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
wdc0 at isa0 port 0x1f0/8 irq 14
wd0 at wdc0 channel 0 drive 0: <TOSHIBA MK2103MAV>
wd0: 16-sector PIO, LBA, 2067MB, 4233600 sectors
wd0(wdc0:0:0): using BIOS timings
sb0 at isa0 port 0x220/24 irq 5 drq 1: dsp v3.01
midi0 at sb0: <SB MIDI UART>
audio0 at sb0
opl0 at sb0: model OPL3
midi1 at opl0: <SB Yamaha OPL3>
wss0 at isa0 port 0x530/8 irq 10 drq 0: CS4231 or AD1845 (vers 4)
audio1 at wss0
pcppi0 at isa0 port 0x61
midi2 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask eb4d netmask eb4d ttymask fbcf
pctr: 586-class performance counters and user-level cycle counter enabled
rtw0 at cardbus0 dev 0 function 0 "Realtek, Rtl8180" irq 11
rtw0: ver RTL8180D, radio SA2400A, amp SA2411, address 00:50:fc:f1:82:14
ohci1 at cardbus1 dev 0 function 0 "Acer Labs M5237 USB" rev 0x03: irq 11,
version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: Acer Labs OHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ohci2 at cardbus1 dev 0 function 1 "Acer Labs M5237 USB" rev 0x03: irq 11,
version 1.0, legacy support
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
usb2 at ohci2: USB revision 1.0
uhub2 at usb2
uhub2: Acer Labs OHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ohci3 at cardbus1 dev 0 function 2 "Acer Labs M5237 USB" rev 0x03: irq 11,
version 1.0, legacy support
usb3 at ohci3: USB revision 1.0
uhub3 at usb3
uhub3: Acer Labs OHCI root hub, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at cardbus1 dev 0 function 3 "Acer Labs M5239 USB2" rev 0x01: irq 11
ehci0: reset timeout
ehci0: init failed, error=13
vendor "Acer Labs", unknown product 0x5253 (class serial bus subclass
Firewire, rev 0x00) at cardbus1 dev 0 function 4 not configured
umass0 at uhub1 port 1 configuration 1 interface 0
umass0: Cypress Semiconductor USB2.0 Storage Device, rev 2.00/0.01, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets
sd0 at scsibus0 targ 1 lun 0: <Maxtor 6, Y080L0, 0000> SCSI0 0/direct fixed
sd0: 78167MB, 78167 cyl, 64 head, 32 sec, 512 bytes/sec, 160086528 sec total
--
b bb o=o=o< o=o=o=o= o=o=o= o<o=o=o=
bbb
http://www.cowlark.com
bbbbbbbbbbbbbbbbbbb
b "I have always wished for my computer to be as easy to use as my
b telephone; my wish has come true because I can no longer figure out how
to
b use my telephone." --- Bjarne Stroustrup
