On Sat, Nov 24, 2007 at 12:13:41PM -0300, Limaunion wrote: > Hi misc! I upgraded my old i486 box to a _new_ pentium 166, but after > less than 24 hours running it I got a kernel crash. I'm sending dmesg > plus some screenshots from ps + trace + show registers.
this looks like a signal jump to a trampoline but is hard to tell w/o poking in pcb (ps /a; x <uarea*>). do you get it often? > Thanks in advance for any comment. > Jorge. > > PS: I've been running memtest86+ during the las 109 hours (229 passes) > without a single error detected. > > screenshot 1: http://img57.imageshack.us/img57/6695/robsd1qx8.jpg > screenshot 2: http://img104.imageshack.us/img104/3669/robsd2xa7.jpg > screenshot 3: http://img217.imageshack.us/img217/3852/robsd3pw3.jpg > screenshot 4: http://img216.imageshack.us/img216/1834/robsd4nx5.jpg > > OpenBSD 4.2 (GENERIC) #375: Tue Aug 28 10:38:44 MDT 2007 > [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC > cpu0: Intel Pentium/MMX ("GenuineIntel" 586-class) 167 MHz > cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,MMX > cpu0: F00F bug workaround installed > real mem = 66678784 (63MB) > avail mem = 55799808 (53MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 07/15/95, BIOS32 rev. 0 @ 0xfdb80 > apm0 at bios0: Power Management spec V1.2 (BIOS mgmt disabled) > apm0: APM power management enable: power management disabled (1) > apm0: APM engage (device 1): power management disabled (1) > apm0: AC on, battery charge unknown > apm0: flags b0102 dobusy 0 doidle 1 > pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000 > pcibios0: PCI BIOS has 5 Interrupt Routing table entries > pcibios0: PCI Interrupt Router at 000:07:0 ("Intel 82371AB PIIX4 ISA" > rev 0x00) > pcibios0: PCI bus #0 is the last bus > bios0: ROM list: 0xc0000/0x8000 > cpu0 at mainbus0 > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > pchb0 at pci0 dev 0 function 0 "Intel 82439TX System" rev 0x01 > piixpcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x01 > pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA, > channel 0 wired to compatibility, channel 1 wired to compatibility > wd0 at pciide0 channel 0 drive 0: <WDC AC310200R> > wd0: 16-sector PIO, LBA, 9787MB, 20044080 sectors > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 > pciide0: channel 1 disabled (no drives) > uhci0 at pci0 dev 7 function 2 "Intel 82371AB USB" rev 0x01: irq 12 > piixpm0 at pci0 dev 7 function 3 "Intel 82371AB Power" rev 0x01: SMBus > disabled > xl0 at pci0 dev 8 function 0 "3Com 3c905B 100Base-TX" rev 0x30: irq 9, > address 00:01:02:87:fc:88 > exphy0 at xl0 phy 24: 3Com internal media interface > xl1 at pci0 dev 9 function 0 "3Com 3c905B 100Base-TX" rev 0x30: irq 10, > address 00:01:02:6e:c5:08 > exphy1 at xl1 phy 24: 3Com internal media interface > vga1 at pci0 dev 10 function 0 "S3 Trio32/64" rev 0x54 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > isa0 at piixpcib0 > isadma0 at isa0 > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pcppi0 at isa0 port 0x61 > midi0 at pcppi0: <PC speaker> > spkr0 at pcppi0 > lpt0 at isa0 port 0x378/4 irq 7 > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > usb0 at uhci0: USB revision 1.0 > uhub0 at usb0: Intel UHCI root hub, rev 1.00/1.00, addr 1 > biomask f965 netmask ff65 ttymask ffe7 > pctr: 586-class performance counters and user-level cycle counter enabled > dkcsum: wd0 matches BIOS drive 0x80 > root on wd0a swap on wd0b dump on wd0b > WARNING: / was not properly unmounted > -- paranoic mickey (my employers have changed but, the name has remained)
