Hi. I get this on booting bsd.rd. I have disable all bells in BIOS
leaving almost only pciide and serial. Playing with bsd -c did not
help either. What info should I provide next?
>> OpenBSD/i386 BOOT 3.01
boot>
booting hd0a:/bsd: 4995572+874168 [52+190496+176373]=0x5f2b6c
entry point at 0x200120*
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2008 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 4.3-current (RAMDISK_CD) #661: Sun Mar 30 23:52:04 MDT 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Intel(R) Pentium(R) 4 CPU 3.00GHz ("GenuineIntel" 686-class) 3.02 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS
H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,EST,CNXT-ID,CX16,
xTPR
real mem = 1064857600 (1015MB)
avail mem = 1023254528 (975MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 01/04/06, BIOS32 rev. 0 @
0xfb290, SMBIOS rev. 2.3 @ 0xf0100 (39 entries)
bios0: vendor Award Software International, Inc. version "F6" date 01/04/2006
bios0: Gigabyte Technology Co., Ltd. 8I945G
apm0 at bios0: Power Management spec V1.2
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 3.0 @ 0xf0000/0xd974
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfd860/224 (12 entries)
pcibios0: PCI Exclusive IRQs: 5 10 11 12
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801GH LPC" rev 0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0xa800!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82945G Host" rev 0x02
vga1 at pci0 dev 2 function 0 "Intel 82945G Video" rev 0x02
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
ppb0 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01: irq 11
pci1 at ppb0 bus 1
ppb1 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xe1
pci2 at ppb1 bus 2
ichpcib0 at pci0 dev 31 function 0 "Intel 82801GB LPC" rev 0x01: PM disabled
pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev 0x01: DMA,
channel 0 configured to compatibility, channel 1 configured to
compatibility
wd0 at pciide0 channel 0 drive 0: <FUJITSU MPE3084AE>
wd0: 16-sector PIO, LBA, 8063MB, 16514064 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
"Intel 82801GB SMBus" rev 0x01 at pci0 dev 31 function 3 not configured
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
biomask f7ed netmask f7ed ttymask ffef
rd0: fixed, 3800 blocks
uvm_fault(0xd06fe100, 0x0, 0, 1) -> e
fatal page fault (6) in supervisor mode
trap type 6 code 0 eip d02d0acf cs 8 eflags 10297 cr2 0 cpl 0
panic: trap type 6, code=0, pc=d02d0acf
syncing disks... done
dumping to dev 1101, offset 0
dump error 19
rebooting...
