Matthew Caron wrote: > > > 64Bit PCI devices are hard to find. I don't have a other device. I can't > > test it, sorry. > Oh, I'm not asking you to test anything like that - I was just telling > you for future reference. We've already done that at work. I'll remember that. But it would be interresting to do some own tests.
> > I've taken a look at that datasheet. I guess you reffer to the topic: > > Southbridge with an Integrated PCI-PCI Bus Bridge. I don't know why they > > hat the tight timing. And I really have no idea why 2 66MHz 64Bit PCI > > cards don't work. > They should work, if all the timings are 100% on, but they don't always. > For example, at work the Ethernet card and SCSI card are fine together, > but toss in the RAID card with either of them and you get lots of errors. Which type of RAID Controller did you use ? [PCI SLOTS] > I will try it in another slot. For some strange reason sometimes the buz will also work well if it has to share its IRQ. > > I have not loaded any usb stuff. My system means about acpi: > > 9: 0 0 XT-PIC acpi > Hmm. ACPI does config of PnP stuff. I wonder if the Buz is getting set > up differently or something because of it. I have now disabled the ACPI in the Bios and it still works. > >>>The buz works too. > >>>Currently The cards are aligend that way in my board: > >>>bottom 32 bit PCI slot Ensoniq ES1371 (es1371) > >>> 2nd 32 bit PCI slot Zoran Corporation ZR36057PQC (buz) > >>> 3rd 32 bit PCI slot Brooktree Corporation Bt878 (bttv) > >>> top 32 bit PCI slot Creative Labs SB Live! (emul10k1) > >>> 1st 64 bit PCI slot Adaptec AIC-7892A U160/m > >>> 2nd 64 bit PCI slot empty > >>> AGP slot Matrox G550 AGP > >> > >>Hmmm... This doesn't make much sense that it would work for you and not > >>for me, in both cases. > > > > Right. Where do you have else differnce (video card...) ? > > Sapphire Atlantis (ATI Radeon) 9100. AGP Slot. DRI enabled. Nothing in > any 64 bit slots. Buz in top PCI slot, Hauppage Digital XG in 1 from > bottom slot. I guess that the cards should not cause any problems. I have also DRI enabled. > >>2.) Are you using ACPI? > > Also the default. That would mean that is is enabled. > But it also has to be enabled in the kernel. It is now off in the bios. I have enabled it, but did not load the modules. > > BTW: I have a "problem" with my board. The VRM2 gets really warm 72�C. > > The VRM1 has only 50�C. The CPU 1/2 56/61 �C. Do you have similar > > temperatures. > No. They are both stable at 45C under load (load = Return to Castle > Wolfenstein for 4 hours). They used to get hotter before I put in 3 case > fans. The CPU's are always +/- 1C of each other. OK. My case has a very good noise prevention. That makes some increase of the temperature in the case. I have only two case fans running at lower speed. The computer is very sillent :) auf hoffentlich bald, Berni the Chaos of Woodquarter Email: [EMAIL PROTECTED] [EMAIL PROTECTED] www: http://www.lysator.liu.se/~gz/bernhard ------------------------------------------------------- This SF.Net email sponsored by: Free pre-built ASP.NET sites including Data Reports, E-commerce, Portals, and Forums are available now. Download today and enter to win an XBOX or Visual Studio .NET. http://aspnet.click-url.com/go/psa00100003ave/direct;at.aspnet_072303_01/01 _______________________________________________ Mjpeg-users mailing list [EMAIL PROTECTED] https://lists.sourceforge.net/lists/listinfo/mjpeg-users
