Thanks, Tom! --Craig
----- Original Message ----- From: "Smith, Tom" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Thursday, April 25, 2002 10:28 AM Subject: Mast-Step Check out this site Craig. Dwyer will at least give you an idea of what I'm talking about... http://www.dwyermast.com/plates.htm Tom Smith Itron Inc. Phone: 509-928-1707 ext. 248 Fax: 509-928-2581 E-mail: [EMAIL PROTECTED] Website: www.linesoft.com Knowledge to Shape Your Future -----Original Message----- From: Honshells [mailto:[EMAIL PROTECTED]] Sent: Wednesday, April 24, 2002 7:22 PM To: [EMAIL PROTECTED] Subject: M_Boats: Mast-Step I'm not familiar with deck-plates, Tom: Can you give me more detail? A piece of hardware that goes under the mast-step and has attachment points? External on the top of the cabin? Thanks! --Craig ----- Original Message ----- From: "Smith, Tom" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Wednesday, April 24, 2002 4:22 PM Subject: Mast-Step If you are going to the trouble of rebedding the mast step, why not install a deck plate at the same time. A plate gives you some nice options for attaching blocks, boom vang, etc. Tom Smith and Jane Van Winkle M15/345 -- Chukar Sandpoint, Idaho -----Original Message----- From: Howard Audsley [mailto:[EMAIL PROTECTED]] Sent: Wednesday, April 24, 2002 5:07 AM To: [EMAIL PROTECTED] Subject: Re: M_Boats: Mast-Step On 4/23/02 9:54 PM, "Honshells" <[EMAIL PROTECTED]> wrote: > > Has anyone rebed their M17's (perhaps the M15's is the same) mast-step? Was > it difficult to remove? What sealant did you use? Can anyone recommend any > other mast-step/compression-post maintenance, other than rebedding the step > for water-tightness? > > Thanks! > > > > _______________________________________________ > http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats > I did mine last year. It is important to note that the mast-step is over an area with balsa core. I was hunting for leaks, so I decided to go after this too. The bolt holes are either 1/4" or 5/16ths". I drilled those out to at least 3/8" from the top, and 1/2" on the bottom. I then used a Dremmel tool with the saw blade to ream out a core area between the two sandwich layers. This was filled with thickened epoxy that seals the hole and serves as a compression post or plug in the core area. The holes for the mast-step were then re-drilled and bedded with boatlife caulk. At the same time, I also sealed the core area exposed by the light socket plug, which is adjacent to the mast step. Actually, I removed every bolt that goes through the cabin deck core areas (there are several), drilled the holes out oversized, backfilled with epoxy, re-drilled and bedded. This included not only the mast-step and light plug, but also both handrails, a winch, and turning blocks and cleat for the topping lift. So far, the deck leaks have stopped. Howard _______________________________________________ http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats _______________________________________________ http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats _______________________________________________ http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats _______________________________________________ http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats _______________________________________________ http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats
