Hmmm. A rough road. I need to sandblast and paint the trailer so I think I will attempt to block up the hull. Much is left to do. Thanks. ---L
-----Original Message----- From: Wayne Yeargain [mailto:[EMAIL PROTECTED] Sent: Thursday, July 22, 2004 3:32 PM To: For and about Montgomery Sailboats Subject: Re: M_Boats: M15 and Centerboard Question My CB freed up while on the trailer by my loosening the pendant and traveling a rough stretch of highway Wayne ----- Original Message ----- From: "Hughston, Larry" <[EMAIL PROTECTED]> To: "'For and about Montgomery Sailboats'" <[EMAIL PROTECTED]> Sent: Thursday, July 22, 2004 11:24 AM Subject: RE: M_Boats: M15 and Centerboard Question > Bob, I have tried that but it appears frozen after four years of > disuse by the previous owner. I think will have to lift the boat off the trailer > entirely and work on it (safely) in that condition. -----L M-15 hull # > 189 > > -----Original Message----- > From: Bob [mailto:[EMAIL PROTECTED] > Sent: Thursday, July 22, 2004 8:24 AM > To: For and about Montgomery Sailboats > Subject: Re: M_Boats: M15 and Centerboard Question > > > Larry > You should be able to pull the centerboard line and ' bump' the board > up a bit while on the trailer. Bump it up and down about 1/4 inch. > > Hughston, Larry wrote: > > >Brian, On my M-15 I have not yet tested to see if the centerboard > >drops. I just got this M-15 a few weeks ago and needs some minor but > >time consuming work before I launch. My question is, should I be > >concerned about visible rust coming through the gelcoat at the > >centerboard pin? Is this replaceable or should I not worry about it? > >This Monty has been in a good deal of salt water in the San Diego > >area by > the previous owner. > > > >Thanks for any information on this. Larry, hull # 189, Sacramento. > > > >-----Original Message----- > >From: Brian Ripley [mailto:[EMAIL PROTECTED] > >Sent: Thursday, July 22, 2004 2:55 AM > >To: [EMAIL PROTECTED]; For and about Montgomery Sailboats > >Subject: Re: M_Boats: M15 and Centerboard Question > > > > > >I replaced mine while anchored. It took a few dives, with nothing > >more than a face mask, but wasn't too difficult. It would have been > >even easier if I had realized early on that the end of the rope > >needed to be decored in order to get it to fit in the hole in the > >centerboard. > > > >Brian Ripley > >'88 M15 > >Roseville, CA > > > >--- Jobst Vandrey <[EMAIL PROTECTED]> wrote: > > > > > >>How does one inspect and change the painter on the M15's > >>centerboard? > >> > >>Can this be done on the trailer, or does it require use of a travel > >>lift. > >> > >>Thanks for any insights > >> > >>Jobst > >> > >> > > > > > > > > > >__________________________________ > >Do you Yahoo!? > >Yahoo! Mail - Helps protect you from nasty viruses. > >http://promotions.yahoo.com/new_mail > > > >_______________________________________________ > >http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats > > > >_______________________________________________ > >http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats > > > > > > > _______________________________________________ > http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats > > _______________________________________________ > http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats > > _______________________________________________ http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats _______________________________________________ http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats
