Hi Matt, Thanks for your reply. I haven't looked inside to see if they're crimped or soldered. Is one easier or better than another? Any idea where I can get the crimper or ejector tool if I need one?
Thanks again, Dave ---- Original Message ---- From: [email protected] To: [email protected] Subject: Re: NEOTEK: Power Supply Connections Date: Tue, 30 Mar 2010 16:22:56 +0100 >Hi Dave >EDACs have 3 possible pin types. >One is for circuit board mounting, which you won't have. >Then there is a crimp type which needs the correct tool to make >connections. >Lastly there is solder type which you obviously solder. >You can get a pin ejector tool which you can release the gold pins >from >the housing if you need to 'reallocate' a few connections. The >ejector >will release all 3 types of pin. >In desperation you can get the pins out using a very fine jewellers >screwdriver as the pins have a 'barb' on one side which lock into the > >plastic moulding. > >Matt S > > > >[email protected] wrote: >> Thanks again Ike, >> I've got an edac snake for the master section. The snake is >labled >> like this: >> >> Cue 1 & 2 In L-R >> Cue A-B In L-R >> Studio Mon In L-R >> Control Room Monitor A In L-R >> Control Room Monitor B In L-R >> Control Room Monitor C In L-R >> 2 Trk 1 In/Out 1-2 (XLR) >> 2 Trk 2 In/Out 1-2 (XLR) >> 2 Trk 3 In/Out 1-2 (XLR) >> 2 Trk 4 In/Out 1-2 (XLR) >> Reverb 1-4 (not sure what these are for) >> >> There are snakes for Pro Tools that I'll have to re-terminate for >my >> Alesis HD24's. I'm going old school for the time being - no >computer! >> I've never used edac connectors before. Is there a tool for making >> the connections inside them? >> >> Thanks again, >> Dave >> >> ---- Original Message ---- >> From: [email protected] >> To: [email protected] >> Subject: Re: NEOTEK: Power Supply Connections >> Date: Tue, 30 Mar 2010 09:48:48 -0400 >> >> >>> Anytime! Feel free to ask whatever you want, whenever you need to. > >>> There's usually somebody available with an answer. >>> Did your console come with cabling/edac connectors? >>> Connector 1 is usually all of the I/O for the master section >>> Including the monitors. >>> Best >>> Ike >>> >>> Sent from my iPhone >>> >>> On 2010-03-29, at 11:50 PM, [email protected] wrote: >>> >>> >>>> Thanks Ike & KB. The Elite is going to be a whole new experience >>>> >>> for >>> >>>> me. I honestly know very little about it and most of my learning >is >>>> going to be from hands on experience. I've never had a board >where >>>> >>> I >>> >>>> couldn't just plug everything in the back. Hopefully I can figure >>>> >>> out >>> >>>> the cabeling for my speakers. That'll be the next step. I'll >>>> >>> probably >>> >>>> show up here from time to time for a bit of help. I'll try not to >>>> >>> bug >>> >>>> you guys too much! >>>> >>>> Thanks again for getting me started! >>>> >>>> Dave Spencer >>>> Morgantown, WV >>>> >>>> ---- Original Message ---- >>>> From: [email protected] >>>> To: [email protected] >>>> Subject: Re: NEOTEK: Power Supply Connections >>>> Date: Mon, 29 Mar 2010 22:45:31 -0400 >>>> >>>> >>>>> HI David, >>>>> Welcome to the list and congratulations on the Elite. They're >>>>> great >>>>> consoles...I love em'. >>>>> Power supply business: >>>>> 1st up, you double up the connections from the power supply at >the >>>>> console end, hence the difference in the number of terminals. >>>>> Connections: >>>>> -18v = -Analog power, color code: Blue and blue/black >>>>> +18v = + Analog power, cc: Red and Red/black >>>>> Bipolar Ground = Analog Phantom Ground, cc: Black, Black/White >>>>> >>> _AND_ >>> >>>>> White/Black (3 wires). The white/black lead is the +48v Ground >at >>>>> >>> the >>> >>>>> PS-3 end. >>>>> +48v = Phantom Power, cc: White >>>>> +36v = Meter Power, cc: Orange >>>>> Meter Ground = Meter Ground, cc: Orange/Black >>>>> -25v = Logic Power, cc: Green >>>>> Logic Ground = Logic Ground, cc: Green/black >>>>> That's it. Take your time, double check your connections and >>>>> then >>>>> check them again...and then power it up. >>>>> Best regards, >>>>> Ike >>>>> >>>>> On 3/29/2010 5:33 PM, [email protected] wrote: >>>>> >>>>>> Greetings to all! I picked up a 1993 Elite. I've made the jump >>>>>> >>> from >>> >>>>> a >>>>> >>>>>> Mackie. I've never had a board like this and I'm needing some >>>>>> >>> help >>> >>>>>> with the power supply connections. Sorry for the freshman >>>>>> >>> question, >>> >>>>>> but I'm trying to get this thing up and running without any >help. >>>>>> >>>>> The >>>>> >>>>>> 12 terminals on the rear of the supply are connected to the >power >>>>>> supply cable, but there are only 8 terminals on the board. I'm >>>>>> >>> not >>> >>>>>> sure which wires connect to which terminals. There are lables >on >>>>>> >>>>> the >>>>> >>>>>> terminals of both the supply and the board, but they are not >all >>>>>> >>>>> the >>>>> >>>>>> same. How can I determine which connections to make? Here are >the >>>>>> >>>>> 12 >>>>> >>>>>> terminals on the rear of the supply, and the 8 terminals on the >>>>>> >>>>> board: >>>>> >>>>>> Supply: >>>>>> 1. -18V >>>>>> 2. -18V >>>>>> 3. Bipolar Ground >>>>>> 4. Bipolar Ground >>>>>> 5. +18V >>>>>> 6. +18V >>>>>> 7. +48V >>>>>> 8. Phantom Ground >>>>>> 9. +35V >>>>>> 10. Meter Ground >>>>>> 11. -25V >>>>>> 12. Logic Ground >>>>>> >>>>>> Board: >>>>>> 1. - analog power >>>>>> 2. + analog power >>>>>> 3. Analog Phantom Ground >>>>>> 4. Phantom Power >>>>>> 5. Logic Ground >>>>>> 6. Logic Power >>>>>> 7. Meter Ground >>>>>> 8. Meter Power >>>>>> >>>>>> ------ >>>>>> >>>>>> View the list online at: >>>>>> >>>>> http://www.mail-archive.com/[email protected] >>>>> >>>>>> You can unsubscribe at anytime by sending an email to >>>>>> >>>>> mailto:[email protected] with "unsubscribe neotek" in the >>>>> message body. If you have any difficulties, or questions >--please >>>>> send an email to mailto:[email protected]. >>>>> >>>>>> The Neotek list is lovingly hosted by Catapult Web. Remember >that >>>>>> >>>>> any message or reply sent to the list will be automatically >>>>> >>> forwarded >>> >>>>> to all subscribers. >>>>> >>>>>> Vive Le Neotek! >>>>>> >>>>>> Thanks. >>>>>> >>>>>> >>>>>> >>>>>> >>>>> -- >>>>> Ike Zimbel >>>>> Zimbel Audio Productions Ltd. >>>>> Toronto >>>>> 416-720-0887 >>>>> >>>>> "Studio House Calls". Authorized Warranty service for Allen& >>>>> >>> Heath, >>> >>>>> Clear-Com, Drawmer, Soundcraft, SPL and Yamaha. Repairs and >>>>> >>> upgrades >>> >>>>> to >>>>> analog audio equipment including: AMEK, dbx, Neve, Neotek, MCI, >>>>> Soundcraft and more. Ask about our RF Frequency co-ordination >>>>> services! >>>>> www.zimbelaudio.com >>>>> >>>>> ------ >>>>> >>>>> View the list online at: >>>>> http://www.mail-archive.com/[email protected] >>>>> >>>>> You can unsubscribe at anytime by sending an email to >>>>> mailto:[email protected] with "unsubscribe neotek" in the >>>>> message body. If you have any difficulties, or questions >--please >>>>> send an email to mailto:[email protected]. >>>>> >>>>> The Neotek list is lovingly hosted by Catapult Web. Remember >that >>>>> >>> any >>> >>>>> message or reply sent to the list will be automatically >forwarded >>>>> >>> to >>> >>>>> all subscribers. >>>>> >>>>> Vive Le Neotek! >>>>> >>>>> Thanks. >>>>> >>>> ------ >>>> >>>> View the list online at: >>>> >>> http://www.mail-archive.com/[email protected] >>> >>>> You can unsubscribe at anytime by sending an email to >>>> >>> mailto:[email protected] >>> >>>> with "unsubscribe neotek" in the message body. If you have any >>>> difficulties, or questions --please send an email to >>>> >>> mailto:[email protected] >>> >>>> . >>>> >>>> The Neotek list is lovingly hosted by Catapult Web. Remember that > >>>> any message or reply sent to the list will be automatically >>>> forwarded to all subscribers. >>>> >>>> Vive Le Neotek! >>>> >>>> Thanks. >>>> >>>> >>> ------ >>> >>> View the list online at: >>> http://www.mail-archive.com/[email protected] >>> >>> You can unsubscribe at anytime by sending an email to >>> mailto:[email protected] with "unsubscribe neotek" in the >>> message body. If you have any difficulties, or questions --please >>> send an email to mailto:[email protected]. >>> >>> The Neotek list is lovingly hosted by Catapult Web. Remember that >any >>> message or reply sent to the list will be automatically forwarded >to >>> all subscribers. >>> >>> Vive Le Neotek! >>> >>> Thanks. >>> >> >> >> ------ >> >> View the list online at: >http://www.mail-archive.com/[email protected] >> >> You can unsubscribe at anytime by sending an email to >mailto:[email protected] with "unsubscribe neotek" in the >message body. If you have any difficulties, or questions --please >send an email to mailto:[email protected]. >> >> The Neotek list is lovingly hosted by Catapult Web. Remember that >any message or reply sent to the list will be automatically forwarded >to all subscribers. >> >> Vive Le Neotek! >> >> Thanks. >> >> >------ > >View the list online at: >http://www.mail-archive.com/[email protected] > >You can unsubscribe at anytime by sending an email to >mailto:[email protected] with "unsubscribe neotek" in the >message body. If you have any difficulties, or questions --please >send an email to mailto:[email protected]. > >The Neotek list is lovingly hosted by Catapult Web. Remember that any >message or reply sent to the list will be automatically forwarded to >all subscribers. > >Vive Le Neotek! > >Thanks. ------ View the list online at: http://www.mail-archive.com/[email protected] You can unsubscribe at anytime by sending an email to mailto:[email protected] with "unsubscribe neotek" in the message body. If you have any difficulties, or questions --please send an email to mailto:[email protected]. The Neotek list is lovingly hosted by Catapult Web. Remember that any message or reply sent to the list will be automatically forwarded to all subscribers. Vive Le Neotek! Thanks.
