Man o man, This is def. going to chase some of you away, but I am not a pro engineer. Anyway some of this terminology could be explained with a little less lingo and more laymans terms. Tie lines? Cue? Also, I have not touched the patch bay on the front of the board. I am only using the punch down panels in the back. Should I be using the foldbacks as the sends, or is that not what you are all saying? Below, you write that aux 1-2 default to foldback and 3-6 are mono inputs. First, I don't think I have 1-6 aux sends, but mianly, that is fine if I did, but how would I individually control each of those aux sends? Thanks all, Colby
Ditto that Furman setup here, but I use the Aux sends (early 80s IIIc) that get patched into tie lines going to room. Aux 1-2 default to foldback and aux 3-6 are the 4 mono inputs. This is for analog sessions. For Pro Tools, just straight outputs to tie lines into Furman. For years I just had the default stereo headphone cue (or 2 mono) and it just didn't cut it after awhile. Musicians love the control of course. The Furman system was one of the best purchases I've made in awhile! b -- Be Hussey www.comp-ny.com -----Original Message----- From: Be Hussey <[email protected]> To: neotek <[email protected]> Sent: Sat, Jul 23, 2011 1:07 am Subject: Re: NEOTEK: Series 2 headphone monitor PLEASE HELP Ditto that Furman setup here, but I use the Aux sends (early 80s IIIc) that get patched into tie lines going to room. Aux 1-2 default to foldback and aux 3-6 are the 4 mono inputs. This is for analog sessions. For Pro Tools, just straight outputs to tie lines into Furman. For years I just had the default stereo headphone cue (or 2 mono) and it just didn't cut it after awhile. Musicians love the control of course. The Furman system was one of the best purchases I've made in awhile! b -- Be Hussey www.comp-ny.com On Jul 22, 2011, at 9:17 PM, Adam Manoucheri <[email protected]> wrote: Hi Colby- I have an early 80's Series 2...I finally got a system wired up, it may not be the best solution, but so far it works for my purposes. I bought a Furman HDS-6 station and a few HR-6 remote controls. It has 4 mono inputs, as well as one stereo pair. The remotes have two headphone jacks, and 5 knobs---volume controls for the 4 mono inputs, and one for the stereo input. They also have a button to include/exclude the mono inputs from the headphone outs. I ended up wiring all 6 inputs into my patchbay, which allows me to patch in what source goes where. For example, I can either have the stereo input mirror the main stereo out of the console, or what I sometimes do is patch the Cue into the L-R inputs of the HDS-6. Then, I can control what goes where via the Q1 and Q2 (or A and B as you described) knobs at each channel, which sends signal to the L and R inputs respectively, whose level is controlled on the remotes by a single stereo level control. I usually patch selected instruments into the 4 mono inputs of the HDS by patching in the channel I want (guitar, bass, etc) at either the insert send or (if it's being used) by routing to a subgroup (if one is open), which also opens up options to blend more than one channel. That's basically my setup, the first remote is attached to the main unit via a pair of Cat5 cables, and additional remotes are daisy-chained off of it. I don't know if that helps you any or not, but it's the compromise I ended up making to get some flexibility. I'm sure others have better ideas, but this was the best I could come up with... ;-) Good luck! Adam Manoucheri Crossroads-Atoll Productions On Jul 22, 2011, at 10:08 PM, Colby Wallace wrote: Someone please help! I can't figure out the puzzle. What are some of your configurations for the musicians to hear the mix. I want each player to be able to say, "hey, I want less bass, and more guitar," etc. I just can't seem to understand how they would be able to adjust those levels in their headphones without it affecting the other headphones. The A and B knobs on each individual channel go to the main "foldback." So, if foldback out goes to a headphone amp, then how would I individually be able to get each headphone their own levels. If I turn down main foldback level A for one person, or B for one person, it affects everyone. I just don't get it. If there was 4 individual outs for headphones with their own a,b,c,d then I would get it, but like this, I dont. Any help would be appreciated. I can't really move forward until I have the headphone setup ideal. I have been working with a very bad headphone setup and cannot take it anymore. Thanks, Colby ps- I bought a headphone amp with 4 headphone jacks, and one line in. Also, the board is a neotek series 2. Mid-80's.
