On Fri, Jan 27, 2017 at 04:00:27PM +0300, Sergei Shtylyov wrote:
> On 01/27/2017 02:04 PM, Simon Horman wrote:
>
> >From: Kazuya Mizuguchi <kazuya.mizuguchi...@renesas.com>
> >
> >This patch enables tx and rx clock internal delay modes (TDM and RDM).
> >
> >This is to address a failure in the case of 1Gbps communication using the
> >by salvator-x board with the KSZ9031RNX phy. This has been reported to
> >occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.
> >
> >With this change APSR internal delay modes are enabled for
> >"rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows:
> >
> >phy mode | ASPR delay mode
> >-----------+----------------
> >rgmii-id | TDM and RDM
> >rgmii-rxid | RDM
> >rgmii-txid | TDM
> >
> >Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi...@renesas.com>
> >Signed-off-by: Simon Horman <horms+rene...@verge.net.au>
> >
> >---
> >v1 [Simon Horman]
> >- Combined patches
> >- Reworded changelog
> >
> >v0 [Kazuya Mizuguchi]
> [...]
> >diff --git a/drivers/net/ethernet/renesas/ravb_main.c
> >b/drivers/net/ethernet/renesas/ravb_main.c
> >index 89ac1e3f6175..9fb4c04c5885 100644
> >--- a/drivers/net/ethernet/renesas/ravb_main.c
> >+++ b/drivers/net/ethernet/renesas/ravb_main.c
> >@@ -1904,6 +1904,29 @@ static void ravb_set_config_mode(struct net_device
> >*ndev)
> > }
> > }
> >
> >+static void ravb_set_delay_mode(struct net_device *ndev)
> >+{
> >+ struct ravb_private *priv = netdev_priv(ndev);
> >+
> >+ if (priv->chip_id != RCAR_GEN2) {
> >+ switch (priv->phy_interface) {
> >+ case PHY_INTERFACE_MODE_RGMII_ID:
> >+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM |
> >+ APSR_DM_TDM);
> >+ break;
> >+ case PHY_INTERFACE_MODE_RGMII_RXID:
> >+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM);
> >+ break;
> >+ case PHY_INTERFACE_MODE_RGMII_TXID:
> >+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_TDM);
> >+ break;
> >+ default:
> >+ ravb_modify(ndev, APSR, APSR_DM, 0);
> >+ break;
> >+ }
> >+ }
> >+}
> >+
> > static int ravb_probe(struct platform_device *pdev)
> > {
> > struct device_node *np = pdev->dev.of_node;
> >@@ -2016,6 +2039,9 @@ static int ravb_probe(struct platform_device *pdev)
> > /* Request GTI loading */
> > ravb_modify(ndev, GCCR, GCCR_LTI, GCCR_LTI);
> >
> >+ /* Set APSR */
> >+ ravb_set_delay_mode(ndev);
> >+
> > /* Allocate descriptor base address table */
> > priv->desc_bat_size = sizeof(struct ravb_desc) * DBAT_ENTRY_NUM;
> > priv->desc_bat = dma_alloc_coherent(ndev->dev.parent,
> > priv->desc_bat_size,
> >@@ -2152,6 +2178,9 @@ static int __maybe_unused ravb_resume(struct device
> >*dev)
> > /* Request GTI loading */
> > ravb_modify(ndev, GCCR, GCCR_LTI, GCCR_LTI);
> >
> >+ /* Set APSR */
> >+ ravb_set_delay_mode(ndev);
> >+
>
> So far the pattern was to first check if gen != 2, then calling a gen3
> specific function. I'd like to keep it, rather than checking in the function
> itself.
So you would like something like?
/* Set APSR */
if (priv->chip_id != RCAR_GEN2)
ravb_set_delay_mode(ndev);
That does not seem better to me but I can make it so if that is your
preference.
