Hi Jose, On 11/09/2018 10:17, Jose Abreu wrote: > On 10-09-2018 19:15, Neil Armstrong wrote: >> >> RX is still ok but now TX fails almost immediately... >> >> With 100ms report : >> >> $ iperf3 -c 192.168.1.47 -t 0 -p 5202 -R -i 0.1 >> Connecting to host 192.168.1.47, port 5202 >> Reverse mode, remote host 192.168.1.47 is sending >> [ 4] local 192.168.1.45 port 45900 connected to 192.168.1.47 port 5202 >> [ ID] Interval Transfer Bandwidth >> [ 4] 0.00-0.10 sec 10.9 MBytes 913 Mbits/sec >> [ 4] 0.10-0.20 sec 11.0 MBytes 923 Mbits/sec >> [ 4] 0.20-0.30 sec 6.34 MBytes 532 Mbits/sec >> [ 4] 0.30-0.40 sec 0.00 Bytes 0.00 bits/sec >> [ 4] 0.40-0.50 sec 0.00 Bytes 0.00 bits/sec >> [ 4] 0.50-0.60 sec 0.00 Bytes 0.00 bits/sec >> [ 4] 0.60-0.70 sec 0.00 Bytes 0.00 bits/sec >> [ 4] 0.70-0.80 sec 0.00 Bytes 0.00 bits/sec >> [ 4] 0.80-0.90 sec 0.00 Bytes 0.00 bits/sec >> [ 4] 0.90-1.00 sec 0.00 Bytes 0.00 bits/sec >> [ 4] 1.00-1.10 sec 0.00 Bytes 0.00 bits/sec >> ^C[ 4] 1.10-1.10 sec 0.00 Bytes 0.00 bits/sec >> - - - - - - - - - - - - - - - - - - - - - - - - - >> [ ID] Interval Transfer Bandwidth >> [ 4] 0.00-1.10 sec 0.00 Bytes 0.00 bits/sec sender >> [ 4] 0.00-1.10 sec 28.2 MBytes 214 Mbits/sec >> receiver >> iperf3: interrupt - the client has terminated >> >> Neil > > Ok, here goes another incremental patch. If this doesn't work can > you please send me a link to the spec of the board you are using ?
Sorry for the delay... Not better, sorry. $ iperf3 -c 10.1.3.201 -p 5202 -R -t 0 Connecting to host 10.1.3.201, port 5202 Reverse mode, remote host 10.1.3.201 is sending [ 4] local 10.1.2.12 port 60612 connected to 10.1.3.201 port 5202 [ ID] Interval Transfer Bandwidth [ 4] 0.00-1.00 sec 110 MBytes 920 Mbits/sec [ 4] 1.00-2.00 sec 110 MBytes 926 Mbits/sec [ 4] 2.00-3.00 sec 1.94 MBytes 16.3 Mbits/sec [ 4] 3.00-4.00 sec 0.00 Bytes 0.00 bits/sec ^C[ 4] 4.00-4.76 sec 0.00 Bytes 0.00 bits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bandwidth [ 4] 0.00-4.76 sec 0.00 Bytes 0.00 bits/sec sender [ 4] 0.00-4.76 sec 222 MBytes 391 Mbits/sec receiver iperf3: interrupt - the client has terminated The board is the Amlogic S400 with the A113D SoC, sorry there is no public spec for this board and for this SoC. Neil > > Thanks and Best Regards, > Jose Miguel Abreu >
