Ciao Giorgio, grazie per la cortesia, la cosa a me non sembra così scontata; il file mgmt.o è nelle mie mani (lo ho dezippato con Windows) e l'ho trasferito sulla partizione Linux in una directory Home\utente\SpeedTouch come suggerito dalle istruzioni. A questo punto le istruzioni dicono di dare il comando: "make install" ........ MA DOVE ? devo dare questo comando ? non sono mica in DOS dove c'era un prompt che aspettava istruzioni. Inoltre cosa intendi per "RPM" ? quei due indirizzi sul sito Mandrake non si aprono da giorni e vanno in: "Impossibile aprire il sito".
io penso di essere ancora in alto mare. ciao Marco ----- Original Message ----- From: <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Friday, January 04, 2002 10:01 AM Subject: Re: [newbie-it] Installazione di un driver > Io ho la versione Mandrake 8.1. In questa il modem viene già > riconosciuto e basta copiare il file mgmt.o su una directory opportuna. > Il file mgmt.o lo si scarica dal sito alcatel. > Se hai l'8.0 ho visto che ci sono due rpm sul sito mandrake > all'indirizzo: > http://www.linux-mandrake.com/it/hard-details.php3?F_TYPE=modem&F_ID=87 > Ciao > Giorgio > > > > Ho scaricato da rete dei file spacciati per driver linux del modem ADS > L Speed Touch USB dal sito dell'Alcatel; > > si chiamano "COPYING", COPYING.GPL", "INSTALL", "MAKEFILE" e "SPEEDTOU > CH.C". > > Sbirciati dentro da Windows i primi due parlano di diritti di copiatur > a, il terzo sono le istruzioni di installazione (che vi riporto di segui > to) il quarto e il quinto sono di vere e proprie istruzioni. > > Trasferiti su Linux il quarto ha il simboletto di un ingranaggio (non > so ancora cosa significhi) e il quinto ha il simboletto forse di una pag > ina (?!?). > > Qualcuno sa spiegarmi in modo un po' meno complicato come devo procede > re ? > > faccio seguire le istruzioni (a mio avviso troppo laboriose) dell'Alca > tel: > > > > ---------------------------------------------------------------------- > ---------------------------------- > > Alcatel SpeedTouch USB Driver Kernel Module > > > > 1. Introduction > > This package contains the kernel module part of the > > Alcatel SpeedTouch USB driver. You will also need the management appli > cation. > > (the Management Application can be found at http://www.alcateldsl.com/ > ) > > This pacakge is distributed under the GPL, see COPYING and COPYING.GPL > for extra info. > > > > 2. Kernel Configuration > > This driver is only supported on kernel 2.4.1 and higher. > > You will need to install this kernel with the following options enable > d: > > > > - > Code maturity level options / Prompt for development and/or incomplete > code/drivers > > - USB support / Support for USB > > - USB support / Preliminary USB device filesystem > > - Networking options / Asynchronous Transfer Mode (ATM) (EXPERIMENTAL) > > > > The first option is necessary to be able to enable ATM. > > When you upgrade your kernel, do not forget to upgrade your modutils! > > (You will need version 2.4.2 or newer) > > The modutils package can be found at: > > > > http://www.kernel.org/pub/linux/utils/kernel/modutils/v2.4/ > > > > > > 3. Compiling the module > > You will need SARLib-0.2.1 to compile this module. > > You can download this library at: > > > > http://sarlib.sourceforge.net/ > > > > Extract the SARLib in the same directory as this package. > > Make sure your new 2.4.1+ kernel is in /usr/src/linux/ > > If it is not the case, you can also modify the path in the Makefile > > Then type: > > > > make > > > > then become root and type: > > > > make install > > > > To be able to use this driver, you will have to install more than thes > e two > > packages. After installation of this package (and plugging in the mode > m) your > > system will feature an ATM device. > > You will need to install PPPoA or PPPoE separately. > > > > > > 4. PPPoE > > Installing PPPoE is the easiest. > > First, install rfc 2684 Bridged ethernet support. This will allow you > to do > > Ethernet over ATM. > > You can download this software from > > > > http://home.sch.bme.hu/~cell/br2684/ > > > > Follow the instructions on this site. (the TUTORIAL file) > > If you want this to be included in your startup you can add the approp > riate > > line in the /etc/hotplug/usb/speedtouch file after the startup of the > > management application. > > > > When you have your bridging ethernet interface (nas0) you can install > a > > PPPoE client. For example, I used roaring penguin PPPoE. > > > > http://www.roaringpenguin.com/pppoe/ > > > > The version 2.8 supports kernel-level PPPoE support too. (see webpage) > > Do not forget to provide 'nas0' as interface name to the rp- > pppoe config. > > > > > > 5. PPPoA > > This is more complex. Save for installing a kernel patch, you will als > o have > > to download the pppd source and patch that. For more information on th > is, > > see: > > > > http://www.sfgoth.com/~mitch/linux/atm/pppoatm/ > > ---------------------------------------------------------------------- > ------------------------------------------ > > ringrazio e saluto > > Marco > > > > > >