I have SB AWE64 ISA PnP card. Here's conf.modules and isapnp.conf
/etc/conf.modules:
alias scsi_hostadapter aic7xxx
alias parport_lowlevel parport_pc
#pre-install pcmcia_core /etc/rc.d/init.d/pcmcia start
alias sound sb
pre-install sound insmod sound dmabuf=1
options opl3 io=0x388
alias midi awe_wave
post-install awe_wave /bin/sfxload /etc/midi/GU11-ROM.SF2
options sb io=0x220 irq=5 dma=1 dma16=5 mpu_io=0x330
alias char-major-107 3dfx
/etc/isapnp.conf:
# $Id: pnpdump.c,v 1.18 1999/02/14 22:47:18 fox Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR
#
# Trying port address 0203
# Trying port address 020b
# Board 1 has serial identifier a6 1d ec 85 d6 e4 00 8c 0e
# (DEBUG)
(READPORT 0x020b)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier a6 1d ec 85 d6 e4 00 8c 0e)
# Vendor Id CTL00e4, Serial Number 502040022, checksum 0xA6.
# Version 1.0, Vendor version 1.0
# ANSI string -->Creative SB AWE64 PnP<--
# Vendor defined tag: 73 02 45 20
#
# Logical device id CTL0045
# Device supports vendor reserved register @ 0x39
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if
required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CTL00e4/502040022 (LD 0
# ANSI string -->Audio<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# IRQ 5.
# High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
(DMA 0 (CHANNEL 1))
# Next DMA channel 5.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
(DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 1 bytes
# Number of IO addresses required: 16
(IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 1 bytes
# Number of IO addresses required: 2
(IO 1 (SIZE 2) (BASE 0x0330))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 4
(IO 2 (SIZE 4) (BASE 0x0388))
# Start dependent functions: priority acceptable
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 5, 6 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))
# Start dependent functions: priority acceptable
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 5, 6 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
# Start dependent functions: priority acceptable
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 5, 6 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Start dependent functions: priority acceptable
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))
# Start dependent functions: priority acceptable
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
# Start dependent functions: priority acceptable
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Start dependent functions: priority functional
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 5, 6 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 16 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0394
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))
# End dependent functions
(NAME "CTL00e4/502040022[0]{Audio }")
(ACT Y)
))
#
# Logical device id CTL7002
# Device supports vendor reserved register @ 0x39
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if
required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CTL00e4/502040022 (LD 1
# Compatible device id PNPb02f
# ANSI string -->Game<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0200
# IO base alignment 1 bytes
# Number of IO addresses required: 8
(IO 0 (SIZE 8) (BASE 0x0200))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0208
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200))
# End dependent functions
(NAME "CTL00e4/502040022[1]{Game }")
(ACT Y)
))
#
# Logical device id CTL0022
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if
required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CTL00e4/502040022 (LD 2
# ANSI string -->WaveTable<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0620
# Maximum IO base address 0x0620
# IO base alignment 1 bytes
# Number of IO addresses required: 4
(IO 0 (BASE 0x0620)) (IO 1 (BASE 0x0A20)) (IO 2 (BASE 0x0E20))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0620
# Maximum IO base address 0x0680
# IO base alignment 32 bytes
# Number of IO addresses required: 4
# (IO 0 (SIZE 4) (BASE 0x0620))
# End dependent functions
# Vendor defined tag: 75 01 69 46 35 55
(NAME "CTL00e4/502040022[2]{WaveTable }")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
hope this helps.
scottw
On 17-Aug-99 pete moss wrote:
> i have mandrake 6.0 and and awe64 gold soundblaster. i am having
> problems getting sound. i only get souind under two conditions. first
> is when kde does its system sounds (startup, shutdown, etc.). second is
> when i run
> 'cat blah.au > /dev/audio'. any programs such as x11amp or the kde
> media player act like they are sending otu sound, but i dont hear
> anything.
> i cant run sndconfig, because it overwrites my isapnp.conf with a
> default version that crashes with my modem. does anyone know what else
> sndconfig does other than write a isapnp.conf file? i may have to set
> this up by hand so that my soundcard will work.
> anyone got any tips? i am a computer musician and i _really_ need to
> get this thing to make sound. i had it working with rh 5.2, so i know
> this is possible.
>
>:P
----------------------------------
E-Mail: scott worley <[EMAIL PROTECTED]>
Date: 17-Aug-99
Time: 19:51:21
This message was sent by XFMail
----------------------------------