Only if I can be assured it won't disable my Win98 Hardware.
----- Original Message -----
From: "Ed Tharp" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Wednesday, January 31, 2001 6:39 AM
Subject: Re: [newbie] Correct NIC module for Realtek8029?
> make sure plug and pray aware OS is turned OFF in your BIOS
> ----- Original Message -----
> From: "Bill Barto" <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Sent: Wednesday, January 31, 2001 2:49 AM
> Subject: Re: [newbie] Correct NIC module for Realtek8029?
>
>
> > /proc/pci says:
> > BUS 0, device 11,function 0
> > Ethernet controller: Realtek 8029(rev 0)
> > Medium devsel
> > I/O at 0xdc40[0xdc41]
> >
> > I happened to notice at bootup a message(they go by so fast)
> > "PCI bios is IRQ 0 which is unlikely to work. Run PCI BIOS setup
> > to assign valid IRQ line"
> >
> > Maybe that's the problem?
> >
> > Bill
> >
> > ----- Original Message -----
> > From: "Lee" <[EMAIL PROTECTED]>
> > To: <[EMAIL PROTECTED]>
> > Sent: Wednesday, January 31, 2001 1:10 AM
> > Subject: Fw: [newbie] Correct NIC module for Realtek8029?
> >
> >
> > > less /proc/pci to look whether your card is pci
> > > and paste how you setup (just command)
> > >
> > >
> > > ----- Original Message -----
> > > From: "Bill Barto" <[EMAIL PROTECTED]>
> > > To: <[EMAIL PROTECTED]>
> > > Sent: Wednesday, January 31, 2001 1:51 PM
> > > Subject: Re: [newbie] Correct NIC module for Realtek8029?
> > >
> > >
> > > > It is currently set up as ne2k-pci but I can't get it set up to work.
> The @home
> > > > workorder has the following:
> > > >
> > > > NIC Provider: @HOME: ISA
> > > >
> > > > I think when it was installed last year they told me they had to use a
> "shared"
> > > > slot. Maybe that's why it's being detected as PCI?
> > > >
> > > > eth0 doesn't even show up when I run ifconfig.
> > > >
> > > > I'm gonna switch to the ISA module and give it a try.
> > > >
> > > > Thanks for the info.
> > > >
> > > > Bill
> > > > ----- Original Message -----
> > > > From: "Digital Wokan" <[EMAIL PROTECTED]>
> > > > To: <[EMAIL PROTECTED]>
> > > > Sent: Wednesday, January 31, 2001 12:27 AM
> > > > Subject: Re: [newbie] Correct NIC module for Realtek8029?
> > > >
> > > >
> > > > > Yes. Unless it's a PCI card, in which case, it should /possibly/ be
> > > > > ne2k-pci.
> > > > >
> > > > > Bill Barto wrote:
> > > > > >
> > > > > > Linux keeps wanting to use NE2000/ne2k for my Realtek8029. Is this
> the correct
> > > > > > module?
> > > > >
> > > > > --
> > > > > Digital Wokan, Tribal Mage of the Electronics Age
> > > > > Guerilla Linux Warrior
> > > > >
> > > >
> > > >
> > > >
> > >
> >
> >
> >
>
>
