Accorning to the navy you can not weld cast metals... It has to do with the micro air pockets crerated in the casting process and when you weld it the weld is going to be MUCH stronder then the materal around it (makes the surounding materal much weaker)... And with a little tab like that alignment is an issue... Best bet is order a new one online.... And i would put money down that thats the last time you break that part... Good luck
-----Original Message----- Date: Friday, July 02, 2010 12:32:25 pm To: [email protected] From: "Noah Goodall" <[email protected]> Subject: Re: [Nighthawk Lovers] Oil change disaster, need some advice Here's the link: http://www.bikebandit.com/houseofmotorcycles/1985-honda-motorcycle-cb450sc-nighthawk-450-lower-crankcase/o/m1968sch4492 It's already been welded, and it didn't work. I'm not sure if it was cast or machined. I don't have a camera but I should be able to upload a photo tonight. I guess the next step is to find a replacement. No salvage yards nearby, and my Nighthawk is my only transportation, so I'll probably have to order the part online. On Fri, Jul 2, 2010 at 12:15 PM, David Cummings < [email protected]> wrote: > Yeah, honestly if a piece is broken off a cast part, it's probably > better and cheaper to find a replacement. Any motorcycle salvage > places near you? > -Dave > > On Fri, Jul 2, 2010 at 12:13 PM, David Cummings > <[email protected]> wrote: > > Like, the engine cases are usually cast aluminum, but the gears are > > machined. Makes a little difference when welding... > > > > The link didn't come through to the schematic > > -Dave > > > > On Fri, Jul 2, 2010 at 12:08 PM, Noah Goodall <[email protected]> > wrote: > >> Right sorry, this is a 1985 Nighthawk 450. Here's a link to the > schematic. > >> Part #4 is what's chipped. Part #5 is what's missing. It's not a > screw > >> on. What do you mean by cast? > >> -Noah > >> > >> On Fri, Jul 2, 2010 at 11:57 AM, David Cummings > >> <[email protected]> wrote: > >>> > >>> First off, which nighthawk is this? I take it it's not a screw-on > >>> filter, otherwise Javier's response would be the best bet. > >>> > >>> Is the cover cast? > >>> -Dave > >>> > >>> On Fri, Jul 2, 2010 at 11:52 AM, Javier Garcia <[email protected]> > >>> wrote: > >>> > Buy a new oil filter. > >>> > > >>> > On Fri, Jul 2, 2010 at 11:33 AM, Noah Goodall < > [email protected]> > >>> > wrote: > >>> >> > >>> >> I don't know how I can massively screw up such a simple operation, > but > >>> >> I > >>> >> did. I changed the oil for the first time last week, but in the > >>> >> process I > >>> >> overtightened the filter cover when it's tab wasn't > >>> >> properly aligned with > >>> >> the matching slot. They were overlapping, which caused the tab to > snap > >>> >> off. > >>> >> I took the filter cover and broken tab and had it welded back > >>> >> together, but > >>> >> the filter cover is still leaking oil. > >>> >> My question is this: is the problem with the filter cover (as in was > it > >>> >> not welded properly and I need a whole new cover) or is it with the > >>> >> washer > >>> >> that goes between the spring and the filter itself (which wasn't > even > >>> >> there > >>> >> when I first got to the filter, and apparently didn't come with the > >>> >> bike > >>> >> when I purchased it)? > >>> >> Any other advice would be greatly appreciated. The bikes been not > >>> >> running > >>> >> for two weeks now and I'm dying to ride! > >>> >> Thanks, > >>> >> Noah > >>> >> > >>> >> -- > >>> >> You received this message because you are sub -- You received this message because you are subscribed to the Google Groups "Nighthawk Motorcycle Lovers!" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/nighthawk_lovers?hl=en.
