I have made changes but it is still the same. That is when the server gets the
lowbat/noAC signal it does shut down as expected but the slave does not.
Perhaps it makes sense for me to list the present settings:
On the Master:
nut.conf MODE=netserver
ups.conf [sdrups] driver = genericups port =
/dev/ttyS1 desc = "For Server & Backup" upstype=9
upsd.conf LISTEN 0.0.0.0
upsd.users [root] password = mypassword
upsmon master instcmds = ALL
upsmon.conf MONITOR root@192.168.0.7 1 sdrups autocadba2 master
On the Slave:
nut.conf MODE=netserver
upsmon.conf MONITOR root@192.168.0.7 1 sdrups autocadba2 slave
Master: 192.168.0.7Slave: 192.168.0.6
Dealing with the firewall I applied the following to both the master and slave:
sudo iptables -A INPUT -p tcp --dport 3493 -j ACCEPT
I have looked in the log files but have not seen anything to suggest a problem.
Steve
Subject: Re: [Nut-upsuser] Master Works, Slave Does Not
From: clep...@gmail.com
Date: Sat, 8 Nov 2014 09:00:12 -0500
CC: nut-upsuser@lists.alioth.debian.org
To: sd_r...@hotmail.com
[Please use reply-all to keep the discussion on the list, thanks]
On Nov 6, 2014, at 10:19 PM, Charles Lepple <clep...@gmail.com> wrote:
On Nov 6, 2014, at 12:48 PM, Steve Read <sd_r...@hotmail.com> wrote:
I am presently upgrading my servers. The old ones are running Suse 10.1 and I
am upgrading to the most recent Debian.
What version of NUT on the new systems?
There are a few changes to the configuration files, mostly related to the ACL
lines.
You mentioned you got "driver.version: 2.6.4" from upsc. So it seems like you
have Debian wheezy. Is that the case for both servers?
(What I was really interested in was the output of "dpkg -l nut", since it
shows the Debian-specific version number as well, but wheezy hasn't changed
much. There are a few things still being sorted out in Debian jessie.)
Now this may be a problem but I don't think it is the only one. I really feel
this is a permissions issue.
For example from the master, if I type:
root@backup2:~# sudo upsc sdrups@localhost ups.status
OL
Which is the response I expect, but if I type (also from the master):
root@backup2:~# sudo upsc sdrups@192.168.0.7 ups.status
Error: Connection failure: Connection refused
One thing that has changed since NUT 2.4.x is that the ACL options were
removed, and the defaults for the LISTEN directive were changed to only bind to
localhost. So a "netstat -ta" (trimmed to just show NUT) would look like this:
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address Foreign Address State
...
tcp 0 0 localhost:nut *:* LISTEN
Instead, you want to listen on the wildcard address, so you will want to add
"LISTEN 0.0.0.0" to /etc/nut/upsd.conf. After restarting NUT, netstat should
look like this:
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address Foreign Address State
...
tcp 0 0 *:nut *:* LISTEN
And at that point, you can use the firewall rules to restrict access to just
localhost and your local network.
If you were able to get output from upsc, then it sounds like you got the
driver working. Just in case, here is the UPGRADING document:
https://github.com/networkupstools/nut/blob/master/UPGRADING
Some drivers (apcsmart) have had under-the-hood changes that should be more
beneficial than problematic.
Also, Stan mentioned the following off-list, and it holds true:
upsmon.conf should have a line like this
MONITOR apcusb@192.168.1.235 1 upsmon pass slave
upsd.users should have a matching statement like this
[upsmon]
password = pass
# upsmon master
# or
upsmon slave
The only configuration files that a slave needs are upsmon.conf, nut.conf to
tell the init.system that it is a slave, and possibly an upssched.conf if you
haven enabled that. The others are master-only.
--
Charles Lepple
clepple@gmail
_______________________________________________
Nut-upsuser mailing list
Nut-upsuser@lists.alioth.debian.org
http://lists.alioth.debian.org/cgi-bin/mailman/listinfo/nut-upsuser
