If your X9DRE-TF+ BIOS revision is not R 3.0a. You can use the following file to update.
Mother Board: Super Micro X9DRE-TF+ BIOS Revision: R 3.0a File Name: X9DR7P3_C04.zip http://www.supermicro.com/about/policies/disclaimer.cfm?url=/support/resources/getfile.aspx?ID=2526 2014-06-10 7:41 GMT+08:00 Rune Tipsmark <r...@steait.net>: > Var/adm/messages shows > > Jun 7 01:43:22 zfs10 mac: [ID 469746 kern.info] NOTICE: ixgbe0 registered > Jun 7 01:43:22 zfs10 ixgbe: [ID 611667 kern.info] NOTICE: ixgbe0: Intel > 10Gb Ethernet, ixgbe 1.1.7 > Jun 7 01:43:23 zfs10 mac: [ID 435574 kern.info] NOTICE: ixgbe0 link up, > 1000 Mbps, full duplex > Jun 7 01:43:24 zfs10 mac: [ID 469746 kern.info] NOTICE: ixgbe1 registered > Jun 7 01:43:24 zfs10 ixgbe: [ID 611667 kern.info] NOTICE: ixgbe1: Intel > 10Gb Ethernet, ixgbe 1.1.7 > Jun 7 01:43:26 zfs10 mac: [ID 435574 kern.info] NOTICE: ixgbe1 link up, > 1000 Mbps, full duplex > > I tried looking for new FW from both Intel and SM but none seem to have > any from what I can find. > > I tried connecting only one port on each end as they were different speeds > (one port directly to another server, one port to a 1gbit switch) - no > difference. > Will check the BIOS setting too. > > Br, > Rune > > > -----Original Message----- > From: Dan McDonald [mailto:dan...@omniti.com] > Sent: Monday, June 09, 2014 4:26 PM > To: Rune Tipsmark > Cc: omnios-discuss > Subject: Re: [OmniOS-discuss] Onboard Intel X540-T2 10gbe NIC shows 1gbit > > > On Jun 9, 2014, at 7:14 PM, Rune Tipsmark <r...@steait.net> wrote: > > > As stated above, > > > > Got a Super Micro X9DRE-TF+ with onboard Intel X540 10Gbase-T with a > cat6 cable straight into another server (with Windows) using a PCI-E Intel > X540-T2 10Gbase-T as well. > > > > Both ends are set to autosense, however only 1gbit is detected on > OmniOS, I can force 10Gbit on Windows, but it won't come up because the > other end supports max 1Gbit. > > > > I tried changing link speed manually in OmniOS, no luck, says not > supported. > > > > Why does it not detect proper 10Gbit on the OmniOS end of things? Any > suggestions as how to get this working? > > > > Version is 151010 , tried reinstall already - no difference. > > 10Gig on here should work. I've not had hands-on experience with built-in > ones, but I've used add-on cards with X540 to great success. > > Did you inspect /var/adm/messages for any complaints from "ixgbe"? You're > using cat6, which is good. One silly question --> on the BIOS on the > OmniOS box, did you enable PCIe mappings for only the low 32-bits? That's > a longshot, I know, but it may be an issue. > > ALSO, we recently had someone else on-list post about X540, and it turned > out they needed a firmware upgrade to get it to work. Please make sure > your BIOS and device firmware are up to date. > > Dan > > _______________________________________________ > OmniOS-discuss mailing list > OmniOS-discuss@lists.omniti.com > http://lists.omniti.com/mailman/listinfo/omnios-discuss >
_______________________________________________ OmniOS-discuss mailing list OmniOS-discuss@lists.omniti.com http://lists.omniti.com/mailman/listinfo/omnios-discuss