Cluster Mode I'm running Openfiler 2.2 on two boxes, one is an old p3 733 w/384mb of ram and only one 20gb hdd and a single NIC the other box is running 2.2 as well its specs are 1800mhz duron 512mb ram 1 nic and 4 disks /dev/hda (74gb) /dev/hdb (74gb) /dev/sda (400gb) /dev/sdb (250gb) -on both the HA cluster service report that it is disabled, I did add both hostnames as nodes nsa.mydom.com and nsa1.mydom.com; I suspect that each box requires an additional network interface but I am not sure. Will adding additional nics auto-enable or make available an option to enable Cluster Mode ?
Raid Problems The box in question is the latter of the two listed above 4 disks /dev/hda (74gb) /dev/hdb (74gb) /dev/sda (400gb) /dev/sdb (250gb) My root partition is a software raid 1 created during setup using disk druid I am unable to utilize the remaining free disk space on any disk. I am try to edit the disk via the web interface, but I would be comfortable doing it via the CLI as well. However, I spent alot of time and effort on this in 2.1 and still didn't have any success. I can't create multiple raid volumes,because I can't edit the disks the remaining space reports that it is in use. [EMAIL PROTECTED] ~]# fdisk -l Disk /dev/hda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/hda1 * 1 13 104391 83 Linux /dev/hda2 14 796 6289447+ fd Linux raid autodetect Disk /dev/hdb: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/hdb1 * 1 783 6289416 fd Linux raid autodetect /dev/hdb2 784 905 979965 82 Linux swap / Solaris Disk /dev/sda: 400.0 GB, 400088457216 bytes 255 heads, 63 sectors/track, 48641 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 28993 232881835+ fd Linux raid autodetect Disk /dev/sdb: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 1 28993 232881835+ fd Linux raid autodetect Disk /dev/md0: 6440 MB, 6440288256 bytes 2 heads, 4 sectors/track, 1572336 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/md0 doesn't contain a valid partition table Disk /dev/md1: 238.4 GB, 238470889472 bytes 2 heads, 4 sectors/track, 58220432 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/md1 doesn't contain a valid partition table [EMAIL PROTECTED] ~]# Local Ldap Server I'm not clear on how to set this up, if I understand it correctly Openfiler can be configured to act as a local ldap server-I don't know if I am overlooking something or if perhaps it isn't documented yet could anyone provide a little insight please ? Headless Configuration Openfiler is meant to be managed via the web interface, is it possible to configure ones openfiler appliance so as to restrict ssh access to one of the serial ports ? Can setup be ran via ssh ? Any plans for LCD/Control panel support ? Thank you for your time and effort in replying. -- David Frohwerk Onsite Services Onsite Service Now _______________________________________________ Openfiler-users mailing list [email protected] https://lists.openfiler.com/mailman/listinfo/openfiler-users
