Ok I will do this, however how would I enable this log using the Builds you provided?!
Strange is also that while the first attempt, it asks twice for the PIN, for the second and following connection attempts (I aborded here not to loose start of log because of buffer limitations) it asks only once... On Thu, 29 Sep 2011 21:13:52 +0300, Alon Bar-Lev <alon.bar...@gmail.com> wrote: > This is strange. > The signature just fails > I need opensc logs. > > It returns CKR_GENERAL_ERROR when tries to sign. > > On Thu, Sep 29, 2011 at 12:25 PM, <busin...@reebs.org> wrote: >> So finally I managed to get the log. For some reasons today it worked >> from command line allthough it did not in GUI. Probably some delay >> caused by management interface which is interferring with OpenVPN when >> log ammount is high... >> >> Anyway here is the file _(had to paste it from command prompt), hope >> that helps! >> >> On Thu, 29 Sep 2011 11:00:57 +0300, Alon Bar-Lev >> <alon.bar...@gmail.com> wrote: >>> Well, >>> I need log to be able to help. >>> If th ui canno handle this, try without ui. >>> This UI uses the management interface in order to provide the >>> passphrase at port 11196. >>> You can telnet this port and see management-notes.txt of how to work with >>> it. >>> Or.. To open a bug within the ui so it be able to enable more logging. >>> >>> On Wed, Sep 28, 2011 at 7:01 PM, <busin...@reebs.org> wrote: >>>> This does not work. >>>> >>>> If I set Verb above 7 I get following loop under Command Line and GUI: >>>> >>>> http://imageshack.us/photo/my-images/829/unbenanntrg.jpg/ >>>> >>>> until it fails. >>>> >>>> If I set "log filename.txt" in the configuration file and run from CLI, >>>> it will go up to the point where pin is required but then fail as it >>>> cannot get pin from stdin (btw using win32 version on win Xp and card is >>>> former Cryptoflex from gemalto): >>>> >>>> >>>> On Wed, 28 Sep 2011 18:30:14 +0300, Alon Bar-Lev >>>> <alon.bar...@gmail.com> wrote: >>>>> set verb 255 and log to a file. >>>>> >>>>> On Wed, Sep 28, 2011 at 5:10 PM, <busin...@reebs.org> wrote: >>>>>> Yes now download works!!! >>>>>> >>>>>> However still not able to connect. >>>>>> >>>>>> I tried both command line and GUI. Same issue: >>>>>> >>>>>> 1- After it ask for PIN and I enter PIN it immediately asks for the PIN >>>>>> again >>>>>> 2- It then tries to connect, but nothing happens >>>>>> 3- After 60 seconde it times out >>>>>> 4- Start another connection attempt >>>>>> 5- It asks for PIN and after I enter it it immediately fails and back >>>>>> to point no. 4 until I break >>>>>> >>>>>> Last working version is 009, 010 and 011 have very same issue. >>>>>> >>>>>> Here is the command line LOG (short form): >>>>>> >>>>>> >>>>>> >>>>>> On Wed, 28 Sep 2011 16:04:24 +0300, Alon Bar-Lev >>>>>> <alon.bar...@gmail.com> wrote: >>>>>>> Now? >>>>>>> >>>>>>> On Wed, Sep 28, 2011 at 4:01 PM, <busin...@reebs.org> wrote: >>>>>>>> Alon, >>>>>>>> >>>>>>>> I believe there is a permission issue with the new files: >>>>>>>> >>>>>>>>> Forbidden >>>>>>>>> >>>>>>>>> You don't have permission to access >>>>>>>>> /downloads/users/alonbl/build/opensc- >>>>>>>>> i686-w64-mingw32-011-engine_pkcs11.tar.bz2 on this server. >>>>>>>> >>>>>>>> Regards, >>>>>>>> >>>>>>>> On Wed, 28 Sep 2011 15:40:00 +0300, Alon Bar-Lev >>>>>>>> <alon.bar...@gmail.com> wrote: >>>>>>>>> Use build-011 >>>>>>>>> >>>>>>>>> On Wed, Sep 28, 2011 at 1:39 PM, <busin...@reebs.org> wrote: >>>>>>>>>> >>>>>>>>>> Hi All, >>>>>>>>>> >>>>>>>>>> any clue what is wrong?! :( >>>>>>>>>> >>>>>>>>>> Rgds >>>>>>>>>> >>>>>>>>>> On Sun, 25 Sep 2011 18:38:39 +0200, <busin...@reebs.org> wrote: >>>>>>>>>> > Hello All, >>>>>>>>>> > >>>>>>>>>> > Currently I am having troubles to get the latest build (32bit) of >>>>>>>>>> > prebuild OpenVPN/OpenSC/OpenSSL to work alltogether. These are >>>>>>>>>> > found >>>>>>>>>> > here: >>>>>>>> .... >>>>>>>> >>>>>>>> >>>>>> >>>>>> >>>> >>>> >> _______________________________________________ opensc-devel mailing list opensc-devel@lists.opensc-project.org http://www.opensc-project.org/mailman/listinfo/opensc-devel
