This image at least boots:
http://download.opensuse.org/ports/armv7hl/factory/images/openSUSE-Factory-ARM-JeOS-cubieboard.armv7l-1.12.1-Build269.1.raw.xz
However it fails to activate networking in general (no IPv4 address, no
routes, no gateway, no resolv.conf - yes the LAN DHCP server works
well), so it's still of no use.
On what hardware have these images been tested?
Thanks,
Volker
U-Boot SPL 2015.04-rc3 (Mar 09 2015 - 21:02:35)
DRAM: 1024 MiB
CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2
U-Boot 2015.04-rc3 (Mar 09 2015 - 21:02:35) Allwinner Technology
CPU: Allwinner A10 (SUN4I)
I2C: ready
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment
HDMI connected: Setting up a 1280x1024 hdmi console
In: serial
Out: vga
Err: vga
SCSI: SUNXI SCSI INIT
SATA link 0 timeout.
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
Net: emac
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
2705 bytes read in 70 ms (37.1 KiB/s)
## Executing script at 43100000
switch to partitions #0, OK
mmc0 is current device
6601032 bytes read in 719 ms (8.8 MiB/s)
42667801 bytes read in 3794 ms (10.7 MiB/s)
22591 bytes read in 204 ms (107.4 KiB/s)
Kernel image @ 0x46000000 [ 0x000000 - 0x64b948 ]
## Loading init Ramdisk from Legacy Image at 4a000000 ...
Image Name: Initrd
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 42667737 Bytes = 40.7 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 49000000
Booting using the fdt blob at 0x49000000
Using Device Tree in place at 49000000, end 4900883e
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
...
[ 39.893308] systemd-udevd[1354]: starting version 210
[ 11.930660] Creating dracut based initrd
[ 130.856442] device-mapper: core: cleaned up
Image Name: Boot-Script
Created: Fri Mar 13 01:02:05 2015
Image Type: ARM Linux Script (uncompressed)
Data Size: 2547 Bytes = 2.49 kB = 0.00 MB
Load Address: 00000000
Entry Point: 00000000
Contents:
Image 0: 2539 Bytes = 2.48 kB = 0.00 MB
skiped writing MBR ID for armv7l
[ 132.368539] systemd[1]: systemd 210 running in system mode. (+PAM -LIBWRAP
+AUDIT +SELINUX -IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ +SECCOMP
+APPARMOR)
[ 132.401255] systemd[1]: Detected architecture 'arm'.
Welcome to openSUSE Factory (Tumbleweed) (armv7hl)!
...
Welcome to openSUSE Factory "Tumbleweed" - Kernel 3.19.1-1-default (ttyS0).
linux login:
--
Volker Kuhlmann
http://volker.top.geek.nz/ Please do not CC list postings to me.
--
To unsubscribe, e-mail: [email protected]
To contact the owner, e-mail: [email protected]
