Hi,
Can anyone help me activate the Marvel 88E8056 gigabit Ethernet
controller on my system? It does not seem to be recognized:
Here are two pertinent entries of "lspci" output:
% lspci -vv
...
02:00.0 Ethernet controller: Marvell Technology Group Ltd. Unknown device 4364
(rev 12)
Subsystem: SysKonnect Unknown device 4340
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe0fc000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at 9800 [size=256]
Expansion ROM at fe0c0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
...
05:04.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit
Ethernet Controller (rev 14)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet
Controller (Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 225
Region 0: Memory at feab4000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at b400 [size=256]
Expansion ROM at 88400000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
...
The first Ethernet device shown is the 88E8056.
The second device, the 88E8001 works, though the system configures the
wrong module (a blacklisted one at that!) to drive it.
What can I do to activate this device?
Thanks.
Randall Schulz
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
