I just installed 10.3 on a new stack of hardware, and one of my SATA drives is not found/mounted.... so, I am looking for a little guidance or advice here.
The hardware is: - ASUS M2N-E motherboard (supports 4 SATA2 drives) - SATA1 RAID controller (supports 2 SATA1 drives) - 2x PATA drives connected to IDE0 - 2x SATA drives connected to the RAID card - 3x SATA drives connected to the SATA ports on the motherboard If I check in the BIOS, all drives connected to the motherboard SATA ports are detected correctly. Three of the drives are connected to the motherboard on SATA 1, SATA 2 and SATA 3. SATA 4 is empty. Two of the drives are connected to the SATA1 RAID card (and are working and mounted correctly). The IDE drives are on ODE0 (and work fine). When I boot 10.3 to install, one drive on the motherboard connectors is not found. A clean install of 10.3, and the missing drive is still not found. If I start up the YAST partitioner tool, it only sees 6 SATA drives (2xPATA, 2xSATA on the motherboard and 2x SATA on the RAID card). The missing drive is identical to the one on /dev/sdd. I have double and triple checked the connections - the BIOS shows the missing 320GB drive, so I assume the connections are fine. Something in SUSE is not playing nicely with the drive. I have included a snippet from the boot.msg file (below). Does anyone have any ideas what is going wrong here? I am kinda out of my depth on this one. C. -------------- <6>scsi0 : pata_amd <6>scsi1 : pata_amd <6>ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001f000 irq 14 <6>ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001f008 irq 15 <6>ata1.00: ATA-7: HDT722525DLAT80, V44OA70A, max UDMA/133 <6>ata1.00: 488397168 sectors, multi 1: LBA48 <6>ata1.01: ATA-7: Maxtor 6L200P0, BAH41E00, max UDMA/133 <6>ata1.01: 398297088 sectors, multi 1: LBA48 <6>ata1.00: configured for UDMA/133 <6>ata1.01: configured for UDMA/133 <6>ata2.00: ATAPI: _NEC DVD_RW ND-3550A, 1.05, max UDMA/33 <6>ata2.01: ATAPI: LITE-ON DVD SOHD-167T, 9S16, max UDMA/33 <6>ata2.00: configured for UDMA/33 <6>ata2.01: configured for UDMA/33 <5>scsi 0:0:0:0: Direct-Access ATA HDT722525DLAT80 V44O PQ: 0 ANSI: 5 <5>scsi 0:0:1:0: Direct-Access ATA Maxtor 6L200P0 BAH4 PQ: 0 ANSI: 5 <5>scsi 1:0:0:0: CD-ROM _NEC DVD_RW ND-3550A 1.05 PQ: 0 ANSI: 5 <5>scsi 1:0:1:0: CD-ROM LITE-ON DVD SOHD-167T 9S16 PQ: 0 ANSI: 5 <7>sata_nv 0000:00:07.0: version 3.4 <5>sata_nv 0000:00:07.0: Using ADMA mode <7>PCI: Setting latency timer of device 0000:00:07.0 to 64 <6>scsi2 : sata_nv <6>scsi3 : sata_nv <6>ata3: SATA max UDMA/133 cmd 0xf8822480 ctl 0xf88224a0 bmdma 0x0001dc00 irq 5 <6>ata4: SATA max UDMA/133 cmd 0xf8822580 ctl 0xf88225a0 bmdma 0x0001dc08 irq 5 <6>ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) <4>ata3.00: qc timeout (cmd 0x27) <4>ata3.00: failed to read native max address (err_mask=0x4) <4>ata3: failed to recover some devices, retrying in 5 secs <6>ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) <4>ata3.00: qc timeout (cmd 0x27) <4>ata3.00: failed to read native max address (err_mask=0x4) <3>ata3.00: revalidation failed (errno=-5) <4>ata3: limiting SATA link speed to 1.5 Gbps <4>ata3.00: limiting speed to UDMA7:PIO5 <4>ata3: failed to recover some devices, retrying in 5 secs <6>ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) <4>ata3.00: qc timeout (cmd 0x27) <4>ata3.00: failed to read native max address (err_mask=0x4) <3>ata3.00: revalidation failed (errno=-5) <4>ata3.00: disabled <6>ata3: EH pending after completion, repeating EH (cnt=4) <6>ata3: soft resetting link <6>ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) <6>ata3: EH complete <6>ata4: SATA link down (SStatus 0 SControl 300) <7>PCI: Setting latency timer of device 0000:00:08.0 to 64 <6>scsi4 : sata_nv <6>scsi5 : sata_nv <6>ata5: SATA max UDMA/133 cmd 0xf8824480 ctl 0xf88244a0 bmdma 0x0001c800 irq 11 <6>ata6: SATA max UDMA/133 cmd 0xf8824580 ctl 0xf88245a0 bmdma 0x0001c808 irq 11 <6>ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) <6>ata5.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7 <6>ata5.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 31/32) <6>ata5.00: configured for UDMA/133 <6>ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300) <6>ata6.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133 <6>ata6.00: 625142448 sectors, multi 1: LBA48 NCQ (depth 31/32) <6>ata6.00: configured for UDMA/133 <5>scsi 4:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5 <6>ata5: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 <5>scsi 5:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 <6>ata6: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 <7>sata_sil 0000:01:07.0: version 2.2 <6>scsi6 : sata_sil <6>scsi7 : sata_sil <6>ata7: SATA max UDMA/100 cmd 0xf8826080 ctl 0xf882608a bmdma 0xf8826000 irq 12 <6>ata8: SATA max UDMA/100 cmd 0xf88260c0 ctl 0xf88260ca bmdma 0xf8826008 irq 12 <6>ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 310) <6>ata7.00: ATA-8: SAMSUNG HD501LJ, CR100-10, max UDMA7 <6>ata7.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) <6>ata7.00: configured for UDMA/100 <6>ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 310) <6>ata8.00: ATA-8: SAMSUNG HD501LJ, CR100-10, max UDMA7 <6>ata8.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) <6>ata8.00: configured for UDMA/100 <5>scsi 6:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5 <5>scsi 7:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5 <4>thermal: Unknown symbol acpi_processor_set_thermal_limit <6>BIOS EDD facility v0.16 2004-Jun-25, 7 devices found <6>usbcore: registered new interface driver usbfs <6>usbcore: registered new interface driver hub <5>sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB) <5>sd 0:0:0:0: [sda] Write Protect is off <7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB) <5>sd 0:0:0:0: [sda] Write Protect is off <7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sda:<6>usbcore: registered new device driver usb <7>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver <7>PCI: Setting latency timer of device 0000:00:02.0 to 64 <6>ohci_hcd 0000:00:02.0: OHCI Host Controller <6>ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 <6>ohci_hcd 0000:00:02.0: irq 12, io mem 0xfe02f000 <4> sda1 sda2 sda3 <5>sd 0:0:0:0: [sda] Attached SCSI disk <5>sd 0:0:1:0: [sdb] 398297088 512-byte hardware sectors (203928 MB) <5>sd 0:0:1:0: [sdb] Write Protect is off <7>sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 0:0:1:0: [sdb] 398297088 512-byte hardware sectors (203928 MB) <5>sd 0:0:1:0: [sdb] Write Protect is off <7>sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sdb: sdb1 <5>sd 0:0:1:0: [sdb] Attached SCSI disk <6>usb usb1: new device found, idVendor=0000, idProduct=0000 <6>usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb1: Product: OHCI Host Controller <6>usb usb1: Manufacturer: Linux 2.6.22.13-0.3-bigsmp ohci_hcd <6>usb usb1: SerialNumber: 0000:00:02.0 <6>usb usb1: configuration #1 chosen from 1 choice <6>hub 1-0:1.0: USB hub found <5>sd 4:0:0:0: [sdc] 488397168 512-byte hardware sectors (250059 MB) <5>sd 4:0:0:0: [sdc] Write Protect is off <7>sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00 <5>sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 4:0:0:0: [sdc] 488397168 512-byte hardware sectors (250059 MB) <5>sd 4:0:0:0: [sdc] Write Protect is off <7>sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00 <5>sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sdc: sdc1 <6>hub 1-0:1.0: 8 ports detected <5>sd 4:0:0:0: [sdc] Attached SCSI disk <5>sd 5:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB) <5>sd 5:0:0:0: [sdd] Write Protect is off <7>sd 5:0:0:0: [sdd] Mode Sense: 00 3a 00 00 <5>sd 5:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 5:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB) <5>sd 5:0:0:0: [sdd] Write Protect is off <7>sd 5:0:0:0: [sdd] Mode Sense: 00 3a 00 00 <5>sd 5:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sdd: sdd1 <5>sd 5:0:0:0: [sdd] Attached SCSI disk <5>sd 6:0:0:0: [sde] 976773168 512-byte hardware sectors (500108 MB) <5>sd 6:0:0:0: [sde] Write Protect is off <7>sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00 <5>sd 6:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 6:0:0:0: [sde] 976773168 512-byte hardware sectors (500108 MB) <5>sd 6:0:0:0: [sde] Write Protect is off <7>sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00 <5>sd 6:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sde: sde1 <5>sd 6:0:0:0: [sde] Attached SCSI disk <5>sd 7:0:0:0: [sdf] 976773168 512-byte hardware sectors (500108 MB) <5>sd 7:0:0:0: [sdf] Write Protect is off <7>sd 7:0:0:0: [sdf] Mode Sense: 00 3a 00 00 <5>sd 7:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 7:0:0:0: [sdf] 976773168 512-byte hardware sectors (500108 MB) <5>sd 7:0:0:0: [sdf] Write Protect is off <7>sd 7:0:0:0: [sdf] Mode Sense: 00 3a 00 00 <5>sd 7:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA -- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
