Hi, Thanks very much for your comments and taking time to check the name. Regarding the 'OY-0001', it's for business reason to use 'OY-0001' but not 'OYE-0001'. The 'old' name in the website also will be updated afterward.
Regards, Weijian > Subject: Re: [OpenWrt-Devel] [PATCH] ramips: adding support for OY-0001 > Wireless Router > From: ka...@tweak.net.au > To: younfa...@hotmail.com > CC: openwrt-devel@lists.openwrt.org > Date: Fri, 10 Jul 2015 11:27:55 +0000 > > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > Isn't this normally called the "OYE-0001" ? not "OY-0001" ? The website > and all literature I've seen uses the "OYE-0001" name... > > Regardless, in many places, you have not followed the existing > alphabetical order. > > LiWeijian <younfa...@hotmail.com> wrote: > > From: Tom Deng <2579131...@qq.com> > > > > Adding support for OY-0001 Wireless Router. > > OY-0001 is a wireless router made by oyewifi.com. Below is the details: > > MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN. > > Signed-off-by: Tom Deng <2579131...@qq.com> > > --- > > diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds > > b/target/linux/ramips/base-files/etc/board.d/01_leds > > index 545bd70..fe3a79d 100755 > > --- a/target/linux/ramips/base-files/etc/board.d/01_leds > > +++ b/target/linux/ramips/base-files/etc/board.d/01_leds > > @@ -238,6 +238,10 @@ case $board in > > set_wifi_led "zbtlink:blue:air" > > set_usb_led "zbtlink:blue:usb" > > ;; > > + oy-0001) > > + ucidef_set_led_default "power" "power" "oy:green:power" "1" > > + set_wifi_led "oy:green:wifi" > > + ;; > > wr8305rt) > > ucidef_set_led_default "power" "power" "wr8305rt:sys" "1" > > set_usb_led "wr8305rt:usb" > > diff --git a/target/linux/ramips/base-files/etc/board.d/02_network > > b/target/linux/ramips/base-files/etc/board.d/02_network > > index bc1fc01..9fb3535 100755 > > --- a/target/linux/ramips/base-files/etc/board.d/02_network > > +++ b/target/linux/ramips/base-files/etc/board.d/02_network > > @@ -139,6 +139,7 @@ ramips_setup_interfaces() > > mzk-750dhp | \ > > whr-300hp2 | \ > > whr-600d | \ > > + oy-0001 | \ > > wsr-600 | \ > > wsr-1166 | \ > > wt1520 | \ > > @@ -283,6 +284,11 @@ ramips_setup_macs() > > wan_mac=$(mtd_get_mac_binary devdata 7) > > ;; > > > > + oy-0001) > > + lan_mac=$(mtd_get_mac_binary factory 40) > > + wan_mac=$(mtd_get_mac_binary factory 46) > > + ;; > > + > > w306r-v20) > > lan_mac=$(cat /sys/class/net/eth0/address) > > wan_mac=$(macaddr_add "$lan_mac" 5) > > diff --git a/target/linux/ramips/base-files/lib/ramips.sh > > b/target/linux/ramips/base-files/lib/ramips.sh > > index d2a1856..3d40ab9 100755 > > --- a/target/linux/ramips/base-files/lib/ramips.sh > > +++ b/target/linux/ramips/base-files/lib/ramips.sh > > @@ -400,6 +400,9 @@ ramips_board_detect() { > > *"Zbtlink ZBT-WA05") > > name="zbt-wa05" > > ;; > > + *"OY-0001") > > + name="oy-0001" > > + ;; > > *"ZBT WR8305RT") > > name="wr8305rt" > > ;; > > diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh > > b/target/linux/ramips/base-files/lib/upgrade/platform.sh > > index cedd62b..8f45a84 100755 > > --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh > > +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh > > @@ -116,6 +116,7 @@ platform_check_image() { > > wr6202 |\ > > wr8305rt |\ > > wrtnode |\ > > + oy-0001 |\ > > wt1520 |\ > > wt3020 |\ > > x5 |\ > > diff --git a/target/linux/ramips/dts/OY-0001.dts > > b/target/linux/ramips/dts/OY-0001.dts > > new file mode 100644 > > index 0000000..48b7099 > > --- /dev/null > > +++ b/target/linux/ramips/dts/OY-0001.dts > > @@ -0,0 +1,123 @@ > > +/dts-v1/; > > + > > +/include/ "mt7620a.dtsi" > > + > > +/ { > > + compatible = "ralink,mt7620a-soc"; > > + model = "OY-0001"; > > + > > + chosen { > > + bootargs = "console=ttyS0,115200"; > > + }; > > + > > + palmbus@10000000 { > > + gpio2: gpio@660 { > > + status = "okay"; > > + }; > > + > > + gpio3: gpio@688 { > > + status = "okay"; > > + }; > > + > > + spi@b00 { > > + status = "okay"; > > + > > + m25p80@0 { > > + #address-cells = <1>; > > + #size-cells = <1>; > > + compatible = "w25q128"; > > + reg = <0 0>; > > + linux,modalias = "m25p80", "w25q128"; > > + spi-max-frequency = <10000000>; > > + > > + partition@0 { > > + label = "u-boot"; > > + reg = <0x0 0x30000>; > > + read-only; > > + }; > > + > > + partition@30000 { > > + label = "u-boot-env"; > > + reg = <0x30000 0x10000>; > > + read-only; > > + }; > > + > > + factory: partition@40000 { > > + label = "factory"; > > + reg = <0x40000 0x10000>; > > + read-only; > > + }; > > + > > + partition@50000 { > > + label = "firmware"; > > + reg = <0x50000 0xfb0000>; > > + }; > > + > > + }; > > + }; > > + }; > > + > > + pinctrl { > > + state_default: pinctrl0 { > > + gpio { > > + ralink,group = "i2c", "uartf", "rgmii1", > > "rgmii2", "wled", "nd_sd"; > > + ralink,function = "gpio"; > > + }; > > + }; > > + }; > > + > > + ethernet@10100000 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&ephy_pins>; > > + > > + ralink,port-map = "llllw"; > > + }; > > + > > + gsw@10110000 { > > + ralink,port4 = "ephy"; > > + }; > > + > > + wmac@10180000 { > > + ralink,mtd-eeprom = <&factory 0>; > > + }; > > + > > + gpio-leds { > > + compatible = "gpio-leds"; > > + powerled { > > + label = "oy:green:power"; > > + gpios = <&gpio0 9 1>; > > + }; > > + wifiled { > > + label = "oy:green:wifi"; > > + gpios = <&gpio3 0 1>; > > + }; > > + }; > > + > > + sdhci@10130000 { > > + status = "okay"; > > + }; > > + > > + ehci@101c0000 { > > + status = "okay"; > > + }; > > + > > + ohci@101c1000 { > > + status = "okay"; > > + }; > > + > > + pcie@10140000 { > > + status = "okay"; > > + }; > > + > > + gpio-keys-polled { > > + compatible = "gpio-keys-polled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + poll-interval = <20>; > > + s1 { > > + label = "reset"; > > + gpios = <&gpio0 1 1>; > > + linux,code = <0x198>; > > + }; > > + }; > > +}; > > diff --git a/target/linux/ramips/image/Makefile > > b/target/linux/ramips/image/Makefile > > index 0c28216..2fe5fdd 100644 > > --- a/target/linux/ramips/image/Makefile > > +++ b/target/linux/ramips/image/Makefile > > @@ -866,6 +866,7 @@ Image/Build/Profile/DIR-810L=$(call > > BuildFirmware/CustomFlash/$(1),$(1),dir-810l > > na930_mtd_size=20971520 > > Image/Build/Profile/NA930=$(call > > BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size)) > > Image/Build/Profile/MZK-750DHP=$(call > > BuildFirmware/Default8M/$(1),$(1),mzk-750dhp,MZK-750DHP) > > +Image/Build/Profile/OY-0001=$(call > > BuildFirmware/Default16M/$(1),$(1),oy-0001,OY-0001) > > Image/Build/Profile/Y1=$(call > > BuildFirmware/Default16M/$(1),$(1),Lenovo-y1,Y1) > > Image/Build/Profile/Y1S=$(call > > BuildFirmware/Default16M/$(1),$(1),Lenovo-y1s,Y1S) > > Image/Build/Profile/MLW221=$(call > > BuildFirmware/Default16M/$(1),$(1),mlw221,MLW221) > > @@ -899,6 +900,7 @@ define Image/Build/Profile/Default > > $(call Image/Build/Profile/WHR1166D,$(1)) > > $(call Image/Build/Profile/MZK-750DHP,$(1)) > > $(call Image/Build/Profile/NA930,$(1)) > > + $(call Image/Build/Profile/OY-0001,$(1)) > > $(call Image/Build/Profile/Y1,$(1)) > > $(call Image/Build/Profile/Y1S,$(1)) > > $(call Image/Build/Profile/MLW221,$(1)) > > _______________________________________________ > > openwrt-devel mailing list > > openwrt-devel@lists.openwrt.org > > https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel > > - -- > Sent using Mailpile, Free Software from www.mailpile.is > > -----BEGIN PGP SIGNATURE----- > Version: GnuPG v1.4.11 (GNU/Linux) > > iQIcBAEBAgAGBQJVn6w8AAoJEBmotQ/U1cr2IxwQAJcAJAAU3Xxq13eDCZ7+DaV/ > OTV1SusODWC++4eJ4HxaDFJ6r4RKVo/0B5f8i70HLz+I2r4dWM60E8J7shWoaSsv > K+aV/pUj50klZuzAXpekDitezYSRi2m7l40IcMrF29x+PZYzr6bdeiJOp+BkTrKh > oo7NN9QykgMwmZy+LoKdgoGtwgIWa1oxZHY1ppI2CCIbGiis+eeusyqp6kPvLUee > y4dzGTFk3oend3LP1DGpW8MmOXFVaCksQIs3RhTGgc2IUQ0dpIpbDYVA3MnaRq95 > s824pG++vE0iCnWrpK9ij518GFvRvhn4kTaE6Xy0T/LmgDKq4DGpCZ3en0dVYzeJ > Ln/FyIwvuALFkPEr2WqWXEAvPIPyuUxViOXpL5XRhGQ1Grnhzl0vwMRzKXq6VBus > QvWVzREupNygD+3iHcJ93zOJFSF+AuvlU5JRS+88Lg8URmX8gEC+R7hulO8Cs2Uc > 0TXg1tYmoUS3AJFZWUebQIlvX66gXHYZs+jTMM1zHRSrZ0Xn6DVUFEQ3oxcuhl2k > 12/sGJusstgMyT30HLPLUHBb7fuw7T7f3149uyi4c8L5WYuzo+fNcbSFckBcP4Cw > jTSjr960T1fBfIXTn/Mj7zlDsk3ntzImNg0uwgohqt2SjLUOR20zPhfrgGXT4fN5 > T7K9ToSMM4QcGLaSx0ry > =Qc6u > -----END PGP SIGNATURE-----
_______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel