Support ported from ar71xx.
Tested on hardware: flashing OpenWrt, then downgrading to vendor
firmware, then using regular vendor web interface to upgrade to OpenWrt
(using -factory.bin image). All MACs in vendor firmware were correct,
the only visible quirk was meaningless "Hardware Version:" field in the
web interface page header (one can append "mac" partition contents to
the vendor firmware dump prior to flashing if that's too worrying).
Signed-off-by: Paul Fertser <fercer...@gmail.com>
---
Changes for v2:
- Remove "rev." from board name
- Use a single DTS file; whoever has hardware to port this to the other
similar devices can easily unsplit it later
- Fix label_mac handling (as it's not available in DT)
- Rename gpio_leds to leds DTS section
- Use boardname for LEDs and merge the setup code with buffalo,whr-g301n
- Use 33 MHz for SPI clock (max frequency for READ command acconding to the
chip datasheet)
- Make "firmware" partition 0x3b0000 (3776 kiB) long, covering "mac" and
"lp"
.../ath79/dts/ar7240_dlink_dir-615-e4.dts | 188 ++++++++++++++++++
target/linux/ath79/image/tiny.mk | 16 ++
.../ath79/tiny/base-files/etc/board.d/01_leds | 3 +-
.../tiny/base-files/etc/board.d/02_network | 6 +
.../etc/hotplug.d/firmware/10-ath9k-eeprom | 4 +
5 files changed, 216 insertions(+), 1 deletion(-)
create mode 100644 target/linux/ath79/dts/ar7240_dlink_dir-615-e4.dts
diff --git a/target/linux/ath79/dts/ar7240_dlink_dir-615-e4.dts
b/target/linux/ath79/dts/ar7240_dlink_dir-615-e4.dts
new file mode 100644
index 0000000000..64ee2eb938
--- /dev/null
+++ b/target/linux/ath79/dts/ar7240_dlink_dir-615-e4.dts
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar7240.dtsi"
+
+/ {
+ model = "D-Link DIR-615 E4";
+ compatible = "dlink,dir-615-e4", "qca,ar7240";
+
+ aliases {
+ led-boot = &power_amber;
+ led-failsafe = &power_amber;
+ led-running = &power_green;
+ led-upgrade = &power_amber;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&switch_led_pins>;
+
+ power_green: power_green {
+ label = "dir-615-e4:green:power";
+ gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ power_amber: power_amber {
+ label = "dir-615-e4:amber:power";
+ gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ wps {
+ label = "dir-615-e4:blue:wps";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ };
+
+ lan1 {
+ label = "dir-615-e4:green:lan1";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ lan2 {
+ label = "dir-615-e4:green:lan2";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ lan3 {
+ label = "dir-615-e4:green:lan3";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ lan4 {
+ label = "dir-615-e4:green:lan4";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+
+ wan_amber {
+ label = "dir-615-e4:amber:wan";
+ gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ wan_green {
+ label = "dir-615-e4:green:wan";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan {
+ label = "dir-615-e4:green:wlan";
+ gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+};
+
+&spi {
+ status = "okay";
+ num-cs = <1>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <33000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uboot: partition@0 {
+ reg = <0x0 0x30000>;
+ label = "u-boot";
+ read-only;
+ };
+
+ nvram: partition@30000 {
+ reg = <0x30000 0x10000>;
+ label = "nvram";
+ read-only;
+ };
+
+ firmware: partition@40000 {
+ compatible = "denx,uimage";
+ reg = <0x40000 0x3b0000>;
+ label = "firmware";
+ };
+
+ /*
+ These two partitions are defined by CameoAP99 layout
+ but not needed for vendor firmware: MAC address is taken
+ from "nvram", language pack can be flashed separately.
+
+ mac: partition@3b0000 {
+ reg = <0x3b0000 0x10000>;
+ label = "mac";
+ read-only;
+ };
+
+ lp: partition@3c0000 {
+ reg = <0x3c0000 0x30000>;
+ label = "lp";
+ read-only;
+ };
+ */
+
+ art: partition@3f0000 {
+ reg = <0x3f0000 0x10000>;
+ label = "art";
+ read-only;
+ };
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ /* ethernet MAC is stored in nvram */
+};
+
+ð1 {
+ status = "okay";
+
+ /* ethernet MAC is stored in nvram */
+};
+
+&pcie {
+ status = "okay";
+
+ ath9k: wifi@0,0 {
+ compatible = "pci168c,002b";
+ reg = <0x0000 0 0 0 0>;
+ qca,no-eeprom;
+ /* LAN MAC is supposed to be used for wifi */
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+};
+
+&pinmux {
+ switch_led_pins: pinmux_switch_led_pins {
+ pinctrl-single,bits = <0x0 0x0 0xf8>;
+ };
+};
+
+&uart {
+ status = "okay";
+};
diff --git a/target/linux/ath79/image/tiny.mk b/target/linux/ath79/image/tiny.mk
index 8f867575af..5f6adeac86 100644
--- a/target/linux/ath79/image/tiny.mk
+++ b/target/linux/ath79/image/tiny.mk
@@ -13,6 +13,22 @@ define Device/buffalo_whr-g301n
endef
TARGET_DEVICES += buffalo_whr-g301n
+define Device/dlink_dir-615-e4
+ ATH_SOC := ar7240
+ DEVICE_VENDOR := D-Link
+ DEVICE_MODEL := DIR-615
+ DEVICE_VARIANT := E4
+ IMAGE_SIZE := 3776k
+ FACTORY_IMAGE_SIZE := 3456k
+ IMAGES += factory.bin
+ IMAGE/default := append-kernel | append-rootfs | pad-rootfs
+ IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | check-size
$$$$(IMAGE_SIZE)
+ IMAGE/factory.bin := $$(IMAGE/default) | check-size $$$$(FACTORY_IMAGE_SIZE)
| \
+ pad-to $$$$(FACTORY_IMAGE_SIZE) | append-string "AP99-AR7240-RT-091105-05"
+ SUPPORTED_DEVICES += dir-615-e4
+endef
+TARGET_DEVICES += dlink_dir-615-e4
+
define Device/pqi_air-pen
ATH_SOC := ar9330
DEVICE_VENDOR := PQI
diff --git a/target/linux/ath79/tiny/base-files/etc/board.d/01_leds
b/target/linux/ath79/tiny/base-files/etc/board.d/01_leds
index bb1799c645..29ab7a0473 100755
--- a/target/linux/ath79/tiny/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/tiny/base-files/etc/board.d/01_leds
@@ -8,7 +8,8 @@ board=$(board_name)
boardname="${board##*,}"
case "$board" in
-buffalo,whr-g301n)
+buffalo,whr-g301n|\
+dlink,dir-615-e4)
ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth0"
ucidef_set_led_switch "lan1" "LAN1" "$boardname:green:lan1" "switch0"
"0x02"
ucidef_set_led_switch "lan2" "LAN2" "$boardname:green:lan2" "switch0"
"0x04"
diff --git a/target/linux/ath79/tiny/base-files/etc/board.d/02_network
b/target/linux/ath79/tiny/base-files/etc/board.d/02_network
index 49fccc0b2e..5d0657fa43 100755
--- a/target/linux/ath79/tiny/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/tiny/base-files/etc/board.d/02_network
@@ -35,6 +35,7 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
;;
+ dlink,dir-615-e4|\
netgear,wnr1000-v2|\
netgear,wnr2000-v3|\
netgear,wnr612-v2|\
@@ -75,6 +76,11 @@ ath79_setup_macs()
local board="$1"
case "$board" in
+ dlink,dir-615-e4)
+ lan_mac=$(mtd_get_mac_ascii "nvram" "lan_mac")
+ wan_mac=$(mtd_get_mac_ascii "nvram" "wan_mac")
+ label_mac=$wan_mac
+ ;;
tplink,tl-wr941-v2|\
tplink,tl-wr941n-v7-cn)
base_mac=$(mtd_get_mac_binary u-boot 0x1fc00)
diff --git
a/target/linux/ath79/tiny/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
b/target/linux/ath79/tiny/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 3da95cc161..5952a40195 100644
--- a/target/linux/ath79/tiny/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/tiny/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -14,6 +14,10 @@ case "$FIRMWARE" in
tplink,tl-wr941-v4)
caldata_extract "art" 0x1000 0xeb8
;;
+ dlink,dir-615-e4)
+ caldata_extract "art" 0x1000 0x1000
+ ath9k_patch_mac_crc $(mtd_get_mac_ascii "nvram" "lan_mac") 0x10c
+ ;;
netgear,wnr1000-v2|\
netgear,wnr2000-v3|\
netgear,wnr612-v2|\
--
2.20.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
