#18628: Don't work Wi-Fi. Netgear WNDR3800
-------------------------+-----------------------------------
Reporter: blastpit@… | Owner: developers
Type: defect | Status: new
Priority: normal | Milestone: Barrier Breaker 14.07
Component: base system | Version: Barrier Breaker 14.07
Keywords: |
-------------------------+-----------------------------------
With factory firmware too.
Please help me.
{{{
U-Boot 1.1.4 (May 27 2011 - 14:58:01)
DNI HW ID: 29763654 flash 16MB RAM 128MB (ar7100) U-boot dni25 V0.1
DRAM: b8050000: 0xc0140180
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 265k for U-Boot at: 87fbc000
Reserving 192k for malloc() at: 87f8c000
Reserving 44 Bytes for Board Info at: 87f8bfd4
REServing 36 Bytes for Global Data at: 87f8bfb0
Reserving 128k for boot params() at: 87f6bfb0
Stack Pointer at: 87f6bf98
Now running in RAM - U-Boot at: 87fbc000
id read 0x100000ff
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning - bad CRC, using default environment
BOARD IS NOT CALIBRATED!!!
In: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
CHH:mac: 0 if: 2
CHH:mac:verify: 0 if: 00000002
: cfg1 0xf cfg2 0x7014
in rtl8366s_phy_setup mac=-1476803788
after rtl8366s_initChip ret=0
eth0: 74:44:01:7c:8b:87
eth0 up
CHH:mac: 1 if: 1
CHH:mac:verify: 1 if: 00000001
: cfg1 0xf cfg2 0x7014
in rtl8366s_phy_setup mac=-1476803308
eth1: 74:44:01:7c:8b:87
eth1 up
eth0, eth1
Trying eth0
: unit 0 phy is up...RGMIi 1000Mbps full duplex
#259:ag7100_set_mac_from_link
: pll reg 0x18050010: 0x11110000
: cfg_1: 0x1ff0000
: cfg_2: 0x3ff
: cfg_3: 0x8001ff
: cfg_4: 0xffff
: cfg_5: 0xfffef
: done cfg2 0x7215 ifctl 0x40605060 miictrl 0x22
Client starts...[Listening] for ADVERTISE...Tchecksum bad
checksum bad
checksum bad
Tchecksum bad
T
Retry count exceeded; boot the image as usual
nmrp server is stopped or failed !
Hit any key to stop autoboot: 0
Verifying Checksum ... OK
### SQUASHFS loading 'image/uImage' to 0x80800000
### SQUASHFS load complete: 1118127 bytes loaded to 0x80800000
## Booting image at 80800000 ...
Image Name: MIPS OpenWrt Linux-3.10.49
Created: 2014-10-02 7:03:34 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1118063 Bytes = 1.1 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3
(OpenWrt/Linaro GCC 4.8-2014.04 r42625) ) #3 Wed Oct 1 14:00:51 CEST 2014
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7161 rev 2
[ 0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz,
Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem
0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 32512
[ 0.000000] Kernel command line: board=WNDR3700 console=ttyS0,115200
mtdparts=spi0.0:320k(u-boot)ro,128k(u-boot-
env)ro,15872k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536
bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126052k/131072k available (2369k kernel code, 5020k
reserved, 621k data, 272k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.070000] MIPS: machine is NETGEAR WNDR3700/WNDR3800/WNDRMAC
[ 2.680000] registering PCI controller with io_map_base unset
[ 2.690000] bio: create slab <bio-0> at 0
[ 2.690000] PCI host bridge to bus 0000:00
[ 2.700000] pci_bus 0000:00: root bus resource [mem
0x10000000-0x16ffffff]
[ 2.700000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 2.710000] pci_bus 0000:00: No busn resource found for root bus, will
use [bus 00-ff]
[ 2.710000] pci 0000:00:11.0: invalid calibration data
[ 2.720000] pci 0000:00:12.0: invalid calibration data
[ 2.720000] pci 0000:00:11.0: BAR 0: assigned [mem
0x10000000-0x1000ffff]
[ 2.730000] pci 0000:00:12.0: BAR 0: assigned [mem
0x10010000-0x1001ffff]
[ 2.730000] pci 0000:00:11.0: using irq 40 for pin 1
[ 2.740000] pci 0000:00:12.0: using irq 41 for pin 1
[ 2.740000] Switching to clocksource MIPS
[ 2.750000] NET: Registered protocol family 2
[ 2.750000] TCP established hash table entries: 1024 (order: 1, 8192
bytes)
[ 2.750000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 2.760000] TCP: Hash tables configured (established 1024 bind 1024)
[ 2.760000] TCP: reno registered
[ 2.770000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 2.770000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 2.780000] NET: Registered protocol family 1
[ 2.800000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.800000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA (RTIME
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.810000] msgmni has been set to 246
[ 2.820000] io scheduler noop registered
[ 2.820000] io scheduler deadline registered (default)
[ 2.830000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 2.860000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a
16550A
[ 2.860000] console [ttyS0]Enabled, bootconsole disabled
[ 2.860000] console [ttyS0] enabled, bootconsole disabled
[ 2.880000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 2.880000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 2.890000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 2.900000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 2.900000] Creating 4 MTD partitions on "spi0.0":
[ 2.910000] 0x000000000000-0x000000050000 : "u-boot"
[ 2.910000] 0x000000050000-0x000000070000 : "u-boot-env"
[ 2.920000] 0x000000070000-0x000000ff0000 : "firmware"
[ 2.930000] 2 netgear-fw partitions found on MTD device firmware
[ 2.930000] 0x000000070000-0x000000182440 : "kernel"
[ 2.940000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 2.950000] 0x000000182440-0x000000ff0000 : "rootfs"
[ 2.960000] mtd: partition "rootfs" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 2.970000] mtd: device 4 (rootfs) set to be root filesystem
[ 2.970000] 1 squashfs-split partitions found on MTD device rootfs
[ 2.980000] 0x0000003b0000-0x000000ff0000 : "rootfs_data"
[ 2.990000] 0x000000ff0000-0x000001000000 : "art"
[ 3.000000] Realtek RTL8366S ethernet switch driver version 0.2.2
[ 3.000000] rtl8366s rtl8366s: using GPIO pins 5 (SDA) and 7 (SCK)
[ 3.010000] rtl8366s rtl8366s: RTL8366 ver. 1 chip found
[ 3.040000] libphy: rtl8366s: probed
[ 3.350000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 3.650000] ag71xx ag71xx.1: connected to PHY at rtl8366s:04
[uid=001cc960, driver=Generic PHY]
[ 3.660000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RGMII
[ 3.670000] TCP: cubic registered
[ 3.670000] NET: Registered protocol family 17
[ 3.680000] Bridge firewalling registered
[ 3.680000] 8021q: 802.1Q VLAN Support v1.8
[ 3.690000] VFS: Mounted root (squashfs filesystem) readonly on device
31:4.
[ 3.700000] Freeing unused kernel memory: 272K (8034c000 - 80390000)
procd: Console is alive
procd: - watchdog -
[ 5.710000] usbcore: registered new interface driver usbfs
[ 5.720000] usbcore: registered new interface driver hub-
[ 5.720000]
usbcore: registered new device driver usb
[ 5.730000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.740000] ehci-platform: EHCI generic platform driver
[ 5.750000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.750000] ehci-platform ehci-platform: new USB bus registered,
assigned bus number 1
[ 5.760000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.790000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.790000] hub 1-0:1.0: USB hub found
[ 5.800000] hub 1-0:1.0: 2 ports detected
[ 5.800000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.810000] ohci-platform ohci-platform: Generic Platform OHCI
Controller
[ 5.810000] ohci-platform ohci-platform: new USB bus registered,
assigned bus number 2
[ 5.820000] ohci-platform ohci-platform: irq 14, io mem 0x1c000000
[ 5.890000] hub 2-0:1.0: USB hub found
[ 5.890000] hub 2-0:1.0: 2 ports detected
procd: - preinit -
[ 6.250000] eth0: link up (1000Mbps/Full duplex)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug
level
jffs2 is ready
jffs2 is ready
[ 9.480000] jffs2: notice: (347) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of
xref (0 dead, 0 orphan) found.
switching to overlay
[ 9.510000] eth0: link down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press ENTer to activate this console.
[ 10.700000] NET: Registered protocol family 10
[ 10.720000] nf_conntrack version 0.5.0 (1973 buckets, 7892 max)
[ 10.730000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.740000] Loading modules backported from Linux version
master-2014-05-22-0-gf2032ea
[ 10.750000] Backport generated by backports.git
backports-20140320-37-g5c33da0-
[ 10.760000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.790000] xt_time: kernel timezone is -0000
[ 10.820000] cfg80211: Calling CRDA to update world regulatory domain
[ 10.820000] cfg80211: World regulatory domain updated:
[ 10.830000] cfg80211: DFS Master region: unset
[ 10.830000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, maeirp), (dfs_cac_time)
[ 10.840000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.850000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.860000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.870000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.870000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 10.880000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 10.890000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.900000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/a)
[ 10.940000] PPP generic driver version 2.4.2
[ 10.950000] NET: Registered protocol family 24
procd: - init complete -
[ 17.150000] eth0: link up (1000Mbps/Full duplex)
[ 17.150000] device eth0.1 entered promiscuous mode
[ 17.160000] device eth0 entered promiscuous mode
[ 17.180000] br-lan: port 1(eth0.1) entered forwarding state
[ 17.180000] br-lan: port 1(eth0.1) entered forwarding state
[ 17.210000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 19.180000] br-lan: port 1(eth0.1) entered forwarding state
}}}
--
Ticket URL: <https://dev.openwrt.org/ticket/18628>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets
