Actually, I think Sequence mode is more appropriate than Real Time mode in this case, but I too think that is the answer.
To explain more what (we think) is going on: When you load data with time in ParaView, it goes to a Snap to Timesteps mode where it will visit each unique timestep once regardless of how far apart they are. Thus, ParaView is treating the numerical imprecision of the different times as unique time steps. If you switch to Sequence or Real Time mode, ParaView uses its own time units and will provide an even temporal spacing. There is more information about the different animation modes in the ParaView tutorial. -Ken Sent from my iPad so blame autocorrect. > On Dec 1, 2016, at 11:35 AM, Scott, W Alan <wasc...@sandia.gov> wrote: > > Not sure if this is the correct answer, but try view/ animation View. Then, > change the Mode to Real Time. Enter your start time and end time, and number > of time steps of interest (i.e., 500). > > Is that what you are looking for? > > alan > > -----Original Message----- > From: ParaView [mailto:paraview-boun...@paraview.org] On Behalf Of Huangrui Mo > Sent: Thursday, December 1, 2016 9:54 AM > To: paraview@paraview.org > Subject: [EXTERNAL] [Paraview] Time Synchronization for Case and Geometry > Sequences > > Dear Paraview Developer, > > May you please help me with the following issue: > > Suppose when a solver writes data out, the field data is written in Ensight > format, and the time sequence is streamed in "ensight.case". > Meanwhile, the geometry data is written in VTK format, and the time sequence > is streamed in "paraview.pvd". > At last, let's assume the number of time sequences is 500. > > Then, when loading into paraview, it does not synchronize the cases in a > perfect sense and would show up with 1000 cases. When animating, there is a > slight mismatch in time for the field data and geometry data. > However, if I use the VTK format for both the field and geometry data, then > paraview does a great job to synchronize the data sets. > > Therefore, my question would be that is it possible to handle time > synchronization even for different formats? > > Thank you very much for your time and help, Huangrui > > -- > ***************************************************** > Huangrui Mo, PhD Candidate > Fluid Mechanics > Department of Mechanical & Mechatronics Engineering University of Waterloo > Waterloo, Ontario N2L 3G1, Canada > E-mail: huangrui...@uwaterloo.ca > ***************************************************** > > _______________________________________________ > Powered by www.kitware.com > > Visit other Kitware open-source projects at > http://www.kitware.com/opensource/opensource.html > > Please keep messages on-topic and check the ParaView Wiki at: > http://paraview.org/Wiki/ParaView > > Search the list archives at: http://markmail.org/search/?q=ParaView > > Follow this link to subscribe/unsubscribe: > http://public.kitware.com/mailman/listinfo/paraview > _______________________________________________ > Powered by www.kitware.com > > Visit other Kitware open-source projects at > http://www.kitware.com/opensource/opensource.html > > Please keep messages on-topic and check the ParaView Wiki at: > http://paraview.org/Wiki/ParaView > > Search the list archives at: http://markmail.org/search/?q=ParaView > > Follow this link to subscribe/unsubscribe: > http://public.kitware.com/mailman/listinfo/paraview _______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Search the list archives at: http://markmail.org/search/?q=ParaView Follow this link to subscribe/unsubscribe: http://public.kitware.com/mailman/listinfo/paraview
