Hey HC,
yes I was religious about matching Firmatas between versions. I even had
Koray here looking over my shoulder to see if I was doing anything
stupid. He agreed that all versions of StandardFirmata we tried were
buggy on OSX.
We are using Arduino 18. I don't see OldStandardFirmata anywhere in the
Pduino-0.5beta6 zip I downloaded, nor do I see a StandardFirmataV2.1
anywhere. Are we looking at the same download? What are you referring to?
In short, we've gotten AnalogFirmata to work, but not StandardFirmata
(too big for Atmega8) or StandardFirmataV2_0 (numerous errors). Some of
the student projects require both Analog and Digital outputs, can you
pls point me in the direction of something that works?
I will try changing the baudrate in Firmata V2.0 to 57600 and see what
happens.
Best,
Derek
On 3/9/10 10:38 PM, Hans-Christoph Steiner wrote:
You need to match the versions of the Firmata on the Arduino and the
Firmata on Pd. Also, you should not use Firmata from Arduino 0017, its
buggy. Use Arduino 0018.
For ATMEGA8 using OldStandardFirmata, but before uploading, change the
baud rate in setup() to 57600. That's the only change from Firmata V2.0
to V2.1. V2.0 is 115200 and V2.1 is 57600. Arduino now uses 57600 for
everything.
.hc
On Mar 9, 2010, at 10:10 AM, Derek Holzer wrote:
Yes proper FTDI drivers installed.
The Analog Firmata works, however the Standard Firmata is totally broken.
D.
On 3/9/10 4:27 PM, Greg Pond wrote:
do you have the proper ftdi drivers installed?
http://www.ftdichip.com/Drivers/VCP.htm
good luck.
On Tue, Mar 9, 2010 at 7:22 AM, Derek Holzer <de...@umatic.nl
<mailto:de...@umatic.nl>> wrote:
Hi all,
I'm in the middle of a workshop right now, and nothing I planned
works. All the users on OSX cannot use the Pduino objects. They all
have latest Pd-Extended 0.41.4 and latest Pduino-0.5beta6. They have
all successfully loaded the Standard-FirmataV2 (the Standard-Firmata
is too big for the Atmega8) to an Arduino NG w/ Atmega8.
Then they open arduino-help.pd, use "devices" to determine the
proper port and set the port.
Then I have them test with "pinMode 13 1" followed by "digital 13
1". I see the RX LEDS flash, but the pin 13 LED does nothing. Then I
open [pd DIGITAL-OUTPUT] and use that patch to flash all the digital
outputs, after setting them to output mode in the main patch. Again,
RX lights blink but nothing else.
After that I get long strings of the following:
UNKNOWN INPUT COMMAND: 8 32120
[arduino] warning currently unsupported 160
[arduino] warning currently unsupported 176
This is consistent across every installation, whether PPC or Intel.
We can't really go further with Arduino without fixing this, so I
hope someone can help.
In contrast, I am using Pduino04.beta2 with Pd-extended-0.39 on my
machine and everything works fine. I have also been unble to run any
Pduino with Pd-extended-0.41.4. Installing Pduino04.beta2 with
Pd-extended-0.39 on a couple of machines of the students hasn't been
an effectivbe workaroundm however ([arduino-help.pd] crashes Pd in
this case).
Any suggestions welcome. Is there something I totally missed here????
D.
--
::: derek holzer ::: http://macumbista.net :::
---Oblique Strategy # 48:
"Discover your formulas and abandon them"
_______________________________________________
Pd-list@iem.at <mailto:Pd-list@iem.at> mailing list
UNSUBSCRIBE and account-management ->
http://lists.puredata.info/listinfo/pd-list
--
::: derek holzer ::: http://macumbista.net :::
---Oblique Strategy # 158:
"Think of the radio"
_______________________________________________
Pd-list@iem.at mailing list
UNSUBSCRIBE and account-management ->
http://lists.puredata.info/listinfo/pd-list
----------------------------------------------------------------------------
Mistrust authority - promote decentralization. - the hacker ethic
--
::: derek holzer ::: http://macumbista.net :::
---Oblique Strategy # 67:
"Emphasize the flaws"
_______________________________________________
Pd-list@iem.at mailing list
UNSUBSCRIBE and account-management ->
http://lists.puredata.info/listinfo/pd-list