Oh, well I think I understand your POV. Regards,
aj >-----Original Message----- >From: [EMAIL PROTECTED] >[mailto:[EMAIL PROTECTED] On Behalf Of Robert Ritchey >Sent: Wednesday, July 11, 2007 3:35 PM >To: [email protected] >Subject: Re: [PEDA] Anyone Using Adv Sch 3.2? > >Hi, >The few times I have used it I have had real problems with >split planes and other items. I also have an extensive set of >libraries for SCH that I cannot figure out how to convert to >99SE schematic libraries and the same for my PCB libraries. >None of this is an obvious migration path and I have not had >the time to fuss with it. I am just too busy trying to run my >business so I have lived with the old stuff. If there was a >document on migration I might try to make some progress but I >have not found anything. >Thanks, > >At 12:00 PM 7/11/2007 -0500, [EMAIL PROTECTED] wrote: >>Date: Wed, 11 Jul 2007 09:10:58 -0400 >>From: <[EMAIL PROTECTED]> >>Subject: Re: [PEDA] Anyone Using Adv Sch 3.2? >>To: <[email protected]> >>Message-ID: >> <[EMAIL PROTECTED]> >>Content-Type: text/plain; charset="us-ascii" >>Not using it, no. >>If you already own P98 or P99SE, then IMO it's time to make the move. >>We're going on eight (8) years since it's release...! And though I'll >>freely admit I'm not equipped personally to do the following, it's >>quite likely that one or more of the more advanced members of this >>group can advise you on moving your active design from the V3 >>environment to P99SE with little or no pain. >>Good luck, >>aj >> >> >-----Original Message----- >> >From: [EMAIL PROTECTED] >> >[mailto:[EMAIL PROTECTED] On Behalf Of Robert Ritchey >> >Sent: Tuesday, July 10, 2007 7:05 PM >> >To: [email protected] >> >Subject: [PEDA] Anyone Using Adv Sch 3.2? >> >Hi, >> >Anyone out there still use Adv Sch 3.2 at all? I have had a really >> >strange thing happen to me. I am not sure if an XP update >bit me or >> >what. When I go to the open dialog I cannot see any files on my E: >> >drive except for 1. >> >I have tried all directories and the only file I can see is >one that >> >I was editing a week back. It also will not save the >libraries when >> >I add them. It seems like it will not write the AdvSch.ini file at >> >all. Strange thing is, I got a D-Link NAS and I moved some of the >> >project folders to it and I can read them there but it >still will not >> >update the AdvSch.ini file. If I change any shortcuts they do not >> >last after I exit. I know I should move to 99SE but it is >so fast to >> >do small boards in this and AdvPCB that I still use it. This all >> >worked a month ago, now it doesn't. Any thoughts would be greatly >> >appreciated. >> >Thanks, > >-Bob >-------------------------------------------------------------------- >Robert Ritchey >Quest Engineering & Development >1328 East Cottonwood Lane >Phoenix, AZ 85048-4765 >Tel: (480) 460-2652 >FAX: (480) 460-2653 >E-Mail: [EMAIL PROTECTED] >E-Mail: [EMAIL PROTECTED] >E-Mail: [EMAIL PROTECTED] >E-Mail: [EMAIL PROTECTED] >WWW: www.QuestEngDev.com/ >WWW: www.Smart-Fly.com/ >-------------------------------------------------------------------- > > > >____________________________________________________________ >You are subscribed to the PEDA discussion forum > >To Post messages: >mailto:[email protected] > >Unsubscribe and Other Options: >http://techservinc.com/mailman/listinfo/peda_techservinc.com > >Browse or Search Old Archives (2001-2004): >http://www.mail-archive.com/[EMAIL PROTECTED] > >Browse or Search Current Archives (2004-Current): >http://www.mail-archive.com/[email protected] > > This e-mail transmission and its attachments may contain information from Avtron Manufacturing, Inc. that is proprietary, privileged and/or confidential and is intended exclusively for the person(s) to whom it is addressed. Any use, copying, retention or disclosure by any person other than the intended recipient or the intended recipient's designees is strictly prohibited. If you have received this message in error, please notify the sender immediately by return e-mail and delete all copies. ____________________________________________________________ You are subscribed to the PEDA discussion forum To Post messages: mailto:[email protected] Unsubscribe and Other Options: http://techservinc.com/mailman/listinfo/peda_techservinc.com Browse or Search Old Archives (2001-2004): http://www.mail-archive.com/[EMAIL PROTECTED] Browse or Search Current Archives (2004-Current): http://www.mail-archive.com/[email protected]
