Chris, Bill ... I just pushed another JOD update to the new github repos. The version incremented for all three parts of JOD but no build was triggered. This may have been due to resolving a conflict on manifest.ijs.
The new version is 0.9.994. Eventually I will get the recipe right for updates. John B On Tue, May 22, 2018 at 12:18 PM, John Baker <[email protected]> wrote: > I was looking for an reason to stop testing older versions and a minimum > of 8.04 is as good as any. > > Thanks > > Sent from my iPhone > > > On May 22, 2018, at 11:19 AM, chris burke <[email protected]> wrote: > > > > The current code has a minimum release for builds of 804, see the Changes > > section on page http://code.jsoftware.com/wiki/Addons/GitHub . > > > > > >> On Tue, May 22, 2018 at 10:01 AM, bill lam <[email protected]> wrote: > >> > >> From JAL Build Log > >> > >> 2018 5 22 15 4 35 addons > >> built: general/joddocument0.9.993 j804 > >> general/joddocument0.9.993 j805 general/joddocument0... > >> > >> If you want to continue support j602, then RELEASE needed > >> to be set to that version. Otherwise, from jwiki it said, > >> > >> RELEASE earliest J release supported, e.g. 'j805', or empty if all > >> > >> > >> Вт, 22 мая 2018, John Baker написал(а): > >>> After adding the required FOLDER and resetting the minimum RELEASE I > >> managed to trigger a JAL update from the new GitHub repos. Incrementing > the > >> VERSION for commits is critical. > >>> > >>> The move to GitHub will expose J code to a much wider audience and > >> foster better collaboration. I’d urge all addon authors to try out the > new > >> process. > >>> > >>> > >>> > >>> Sent from my iPhone > >>> > >>>> On May 21, 2018, at 9:22 PM, bill lam <[email protected]> wrote: > >>>> > >>>> rebuild should be automatical without any delay. > >>>> > >>>> In your manifest.ijs you had reverse something that > >>>> are needed/changed since recently. > >>>> > >>>> -RELEASE=: '' > >>>> - > >>>> -FOLDER=: 'general/jod' > >>>> - > >>>> +RELEASE=:'j602 j701 j801 j802 j803 j804 j805 j806 j807' > >>>> > >>>> At least, the FOLDER is mandatory. and RELEASE is the > >>>> minimum version that an addon will support. > >>>> > >>>> > >>>> Пн, 21 мая 2018, John Baker написал(а): > >>>>> I pushed a test JOD update to the jsoftware git repos. The commits > >> show but it didn’t trigger a JAL build. > >>>>> > >>>>> Are the builds scheduled or is there a manual step on your end? > >>>>> > >>>>> Sent from my iPhone > >>>>> > >>>>>> On May 21, 2018, at 12:45 PM, chris burke <[email protected]> > >> wrote: > >>>>>> > >>>>>> Each addon repo has a webhook that is used to update the J server > >> addons. > >>>>>> It sends a "commit" event to the J server so it can update the addon > >> if the > >>>>>> manifest version has been incremented. This is essentially the same > >> as the > >>>>>> old SVN commit event. > >>>>>> > >>>>>> Also, if you wish you can transfer your repos to your personal > github > >>>>>> account. I would encourage you to do so, though it will also be fine > >> to > >>>>>> leave them on the Jsoftware account. To make a transfer, login to > >> github, > >>>>>> view the repo and open Settings. Then in the Danger Zone at the foot > >> of the > >>>>>> Settings page, click the Transfer button and follow the > >> instructions. Once > >>>>>> transferred, you are free to rename it and change access > permissions. > >>>>>> > >>>>>> > >>>>>> > >>>>>>> On Mon, May 21, 2018 at 11:31 AM, John Baker <[email protected]> > >> wrote: > >>>>>>> > >>>>>>> In the next few days I will be committing a minor JOD update to the > >> new > >>>>>>> GitHub addon repos. > >>>>>>> > >>>>>>> I see I am a contributor to the JOD addons and I have set up local > >> git > >>>>>>> versions of them. I haven’t tried committing anything yet because I > >> not > >>>>>>> sure if there is anything else that needs to done to trigger an > >> addon > >>>>>>> build. When changes were committed to the old SVN repos JAL builds > >> were > >>>>>>> kicked off. I presume something similar will happen with the Git > >> repos but > >>>>>>> I fuzzy on the details. > >>>>>>> > >>>>>>> Jdb > >>>>>>> > >>>>>>> Sent from my iPhone > >>>>>>> ------------------------------------------------------------ > >> ---------- > >>>>>>> For information about J forums see http://www.jsoftware.com/ > >> forums.htm > >>>>>> ------------------------------------------------------------ > >> ---------- > >>>>>> For information about J forums see http://www.jsoftware.com/ > >> forums.htm > >>>>> ------------------------------------------------------------ > >> ---------- > >>>>> For information about J forums see http://www.jsoftware.com/ > >> forums.htm > >>>> > >>>> -- > >>>> regards, > >>>> ==================================================== > >>>> GPG key 1024D/4434BAB3 2008-08-24 > >>>> gpg --keyserver subkeys.pgp.net --recv-keys 4434BAB3 > >>>> gpg --keyserver subkeys.pgp.net --armor --export 4434BAB3 > >>>> ------------------------------------------------------------ > ---------- > >>>> For information about J forums see http://www.jsoftware.com/ > forums.htm > >>> ---------------------------------------------------------------------- > >>> For information about J forums see http://www.jsoftware.com/forums.htm > >> > >> -- > >> regards, > >> ==================================================== > >> GPG key 1024D/4434BAB3 2008-08-24 > >> gpg --keyserver subkeys.pgp.net --recv-keys 4434BAB3 > >> gpg --keyserver subkeys.pgp.net --armor --export 4434BAB3 > >> ---------------------------------------------------------------------- > >> For information about J forums see http://www.jsoftware.com/forums.htm > >> > > ---------------------------------------------------------------------- > > For information about J forums see http://www.jsoftware.com/forums.htm > -- John D. Baker [email protected] ---------------------------------------------------------------------- For information about J forums see http://www.jsoftware.com/forums.htm
