That did the trick. Thanks Sent from my iPhone
> On May 27, 2018, at 8:09 PM, bill lam <[email protected]> wrote: > > Perhaps, when you merged commits, the version inside > manifest.ijs did not increment in the correct. Try > $ git pull --rebase > and then increment VERSION again and push again. > > Вс, 27 мая 2018, John Baker написал(а): >> Chris, Bill ... >> >> I just pushed another JOD update to the new github repos. The version >> incremented for all three parts of JOD but no build was triggered. This may >> have >> been due to resolving a conflict on manifest.ijs. >> >> The new version is 0.9.994. >> >> Eventually I will get the recipe right for updates. >> >> John B >> >>> On Tue, May 22, 2018 at 12:18 PM, John Baker <[email protected]> wrote: >>> >>> I was looking for an reason to stop testing older versions and a minimum >>> of 8.04 is as good as any. >>> >>> Thanks >>> >>> Sent from my iPhone >>> >>>> On May 22, 2018, at 11:19 AM, chris burke <[email protected]> wrote: >>>> >>>> The current code has a minimum release for builds of 804, see the Changes >>>> section on page http://code.jsoftware.com/wiki/Addons/GitHub . >>>> >>>> >>>>> On Tue, May 22, 2018 at 10:01 AM, bill lam <[email protected]> wrote: >>>>> >>>>> From JAL Build Log >>>>> >>>>> 2018 5 22 15 4 35 addons >>>>> built: general/joddocument0.9.993 j804 >>>>> general/joddocument0.9.993 j805 general/joddocument0... >>>>> >>>>> If you want to continue support j602, then RELEASE needed >>>>> to be set to that version. Otherwise, from jwiki it said, >>>>> >>>>> RELEASE earliest J release supported, e.g. 'j805', or empty if all >>>>> >>>>> >>>>> Вт, 22 мая 2018, John Baker написал(а): >>>>>> After adding the required FOLDER and resetting the minimum RELEASE I >>>>> managed to trigger a JAL update from the new GitHub repos. Incrementing >>> the >>>>> VERSION for commits is critical. >>>>>> >>>>>> The move to GitHub will expose J code to a much wider audience and >>>>> foster better collaboration. I’d urge all addon authors to try out the >>> new >>>>> process. >>>>>> >>>>>> >>>>>> >>>>>> Sent from my iPhone >>>>>> >>>>>>> On May 21, 2018, at 9:22 PM, bill lam <[email protected]> wrote: >>>>>>> >>>>>>> rebuild should be automatical without any delay. >>>>>>> >>>>>>> In your manifest.ijs you had reverse something that >>>>>>> are needed/changed since recently. >>>>>>> >>>>>>> -RELEASE=: '' >>>>>>> - >>>>>>> -FOLDER=: 'general/jod' >>>>>>> - >>>>>>> +RELEASE=:'j602 j701 j801 j802 j803 j804 j805 j806 j807' >>>>>>> >>>>>>> At least, the FOLDER is mandatory. and RELEASE is the >>>>>>> minimum version that an addon will support. >>>>>>> >>>>>>> >>>>>>> Пн, 21 мая 2018, John Baker написал(а): >>>>>>>> I pushed a test JOD update to the jsoftware git repos. The commits >>>>> show but it didn’t trigger a JAL build. >>>>>>>> >>>>>>>> Are the builds scheduled or is there a manual step on your end? >>>>>>>> >>>>>>>> Sent from my iPhone >>>>>>>> >>>>>>>>> On May 21, 2018, at 12:45 PM, chris burke <[email protected]> >>>>> wrote: >>>>>>>>> >>>>>>>>> Each addon repo has a webhook that is used to update the J server >>>>> addons. >>>>>>>>> It sends a "commit" event to the J server so it can update the addon >>>>> if the >>>>>>>>> manifest version has been incremented. This is essentially the same >>>>> as the >>>>>>>>> old SVN commit event. >>>>>>>>> >>>>>>>>> Also, if you wish you can transfer your repos to your personal >>> github >>>>>>>>> account. I would encourage you to do so, though it will also be fine >>>>> to >>>>>>>>> leave them on the Jsoftware account. To make a transfer, login to >>>>> github, >>>>>>>>> view the repo and open Settings. Then in the Danger Zone at the foot >>>>> of the >>>>>>>>> Settings page, click the Transfer button and follow the >>>>> instructions. Once >>>>>>>>> transferred, you are free to rename it and change access >>> permissions. >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>>> On Mon, May 21, 2018 at 11:31 AM, John Baker <[email protected]> >>>>> wrote: >>>>>>>>>> >>>>>>>>>> In the next few days I will be committing a minor JOD update to the >>>>> new >>>>>>>>>> GitHub addon repos. >>>>>>>>>> >>>>>>>>>> I see I am a contributor to the JOD addons and I have set up local >>>>> git >>>>>>>>>> versions of them. I haven’t tried committing anything yet because I >>>>> not >>>>>>>>>> sure if there is anything else that needs to done to trigger an >>>>> addon >>>>>>>>>> build. When changes were committed to the old SVN repos JAL builds >>>>> were >>>>>>>>>> kicked off. I presume something similar will happen with the Git >>>>> repos but >>>>>>>>>> I fuzzy on the details. >>>>>>>>>> >>>>>>>>>> Jdb >>>>>>>>>> >>>>>>>>>> Sent from my iPhone >>>>>>>>>> ------------------------------------------------------------ >>>>> ---------- >>>>>>>>>> For information about J forums see http://www.jsoftware.com/ >>>>> forums.htm >>>>>>>>> ------------------------------------------------------------ >>>>> ---------- >>>>>>>>> For information about J forums see http://www.jsoftware.com/ >>>>> forums.htm >>>>>>>> ------------------------------------------------------------ >>>>> ---------- >>>>>>>> For information about J forums see http://www.jsoftware.com/ >>>>> forums.htm >>>>>>> >>>>>>> -- >>>>>>> regards, >>>>>>> ==================================================== >>>>>>> GPG key 1024D/4434BAB3 2008-08-24 >>>>>>> gpg --keyserver subkeys.pgp.net --recv-keys 4434BAB3 >>>>>>> gpg --keyserver subkeys.pgp.net --armor --export 4434BAB3 >>>>>>> ------------------------------------------------------------ >>> ---------- >>>>>>> For information about J forums see http://www.jsoftware.com/ >>> forums.htm >>>>>> ---------------------------------------------------------------------- >>>>>> For information about J forums see http://www.jsoftware.com/forums.htm >>>>> >>>>> -- >>>>> regards, >>>>> ==================================================== >>>>> GPG key 1024D/4434BAB3 2008-08-24 >>>>> gpg --keyserver subkeys.pgp.net --recv-keys 4434BAB3 >>>>> gpg --keyserver subkeys.pgp.net --armor --export 4434BAB3 >>>>> ---------------------------------------------------------------------- >>>>> For information about J forums see http://www.jsoftware.com/forums.htm >>>>> >>>> ---------------------------------------------------------------------- >>>> For information about J forums see http://www.jsoftware.com/forums.htm >>> >> >> >> >> -- >> John D. Baker >> [email protected] >> ---------------------------------------------------------------------- >> For information about J forums see http://www.jsoftware.com/forums.htm > > -- > regards, > ==================================================== > GPG key 1024D/4434BAB3 2008-08-24 > gpg --keyserver subkeys.pgp.net --recv-keys 4434BAB3 > gpg --keyserver subkeys.pgp.net --armor --export 4434BAB3 > ---------------------------------------------------------------------- > For information about J forums see http://www.jsoftware.com/forums.htm ---------------------------------------------------------------------- For information about J forums see http://www.jsoftware.com/forums.htm
