Hi Mike, my Box is 29034 rev. C547. It works fine with Ubuntu 9.10. and its 2.6.31-17- generic kernel :
[ 2688.480065] usb 1-2: new high speed USB device using ehci_hcd and address 2 [ 2688.609839] usb 1-2: configuration #1 chosen from 1 choice [ 2688.660768] usbcore: registered new interface driver pvrusb2 [ 2688.660773] pvrusb2: V4L in-tree version:Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/Tuner [ 2688.660776] pvrusb2: Debug mask is 31 (0x1f) [ 2688.662156] pvrusb2: Binding ir_video to i2c address 0x18. [ 2688.695991] saa7115 5-0021: saa7115 found (1f7115d0e100000) @ 0x42 (pvrusb2_a) [ 2688.874250] pvrusb2: Attached sub-driver saa7115 [ 2688.883372] msp3400 5-0040: MSP3415G-B8 found @ 0x80 (pvrusb2_a) [ 2688.883376] msp3400 5-0040: msp3400 supports nicam and radio, mode is autodetect and autoselect [ 2688.883419] pvrusb2: Attached sub-driver msp3400 [ 2688.918549] tuner 5-0061: chip found @ 0xc2 (pvrusb2_a) [ 2688.918555] pvrusb2: Attached sub-driver tuner [ 2688.921463] tuner 5-0043: chip found @ 0x86 (pvrusb2_a) [ 2688.921552] tda9887 5-0043: creating new instance [ 2688.921554] tda9887 5-0043: tda988[5/6/7] found [ 2688.921991] tda9887 5-0043: i2c i/o error: rc == -5 (should be 4) [ 2688.921999] pvrusb2: Attached sub-driver tuner [ 2688.944500] tveeprom 5-0050: Hauppauge model 29034, rev C547, serial# 7203756 [ 2688.944503] tveeprom 5-0050: tuner model is LG TP18PSB01D (idx 47, type 28) [ 2688.944507] tveeprom 5-0050: TV standards PAL(B/G) (eeprom 0x04) [ 2688.944510] tveeprom 5-0050: audio processor is MSP3415 (idx 6) [ 2688.944513] tveeprom 5-0050: decoder processor is SAA7115 (idx 19) [ 2688.944516] tveeprom 5-0050: has radio, has IR receiver, has no IR transmitter [ 2688.944522] pvrusb2: Supported video standard(s) reported available in hardware: PAL-B/B1/G/H;SECAM-B/G/H [ 2688.944527] pvrusb2: Mapping standards mask=0xd000f (PAL-B/B1/G/H;SECAM- B/G/H) [ 2688.944531] pvrusb2: Setting up 9 unique standard(s) [ 2688.944534] pvrusb2: Set up standard idx=0 name=PAL-B/G [ 2688.944537] pvrusb2: Set up standard idx=1 name=SECAM-B/G [ 2688.944540] pvrusb2: Set up standard idx=2 name=PAL-B [ 2688.944543] pvrusb2: Set up standard idx=3 name=PAL-B1 [ 2688.944545] pvrusb2: Set up standard idx=4 name=PAL-G [ 2688.944548] pvrusb2: Set up standard idx=5 name=PAL-H [ 2688.944550] pvrusb2: Set up standard idx=6 name=SECAM-B [ 2688.944553] pvrusb2: Set up standard idx=7 name=SECAM-G [ 2688.944556] pvrusb2: Set up standard idx=8 name=SECAM-H [ 2688.944559] pvrusb2: Initial video standard guessed as PAL-B/B1/G [ 2688.944570] pvrusb2: Device initialization completed successfully. [ 2688.944635] pvrusb2: registered device video1 [mpeg] [ 2688.944655] pvrusb2: registered device radio1 [mpeg] [ 2688.948536] usb 1-2: firmware: requesting v4l-cx2341x-enc.fw [ 2689.286116] tuner-simple 5-0061: creating new instance [ 2689.286122] tuner-simple 5-0061: type set to 28 (LG PAL_BG+FM (TPI8PSB01D)) [ 2689.425745] tda9887 5-0043: i2c i/o error: rc == -5 (should be 4) [ 2689.496867] tda9887 5-0043: i2c i/o error: rc == -5 (should be 4) [ 2689.499740] tda9887 5-0043: i2c i/o error: rc == -5 (should be 4) Those "tda9887 5-0043: i2c i/o error: rc == -5 (should be 4)" came since a long time (I reported this before) and seem to be harmless. I tested it also with http://linuxtv.org/hg/~mcisely/pvrusb2-20100205/ and there are also no problems. Greets, Martin _______________________________________________ pvrusb2 mailing list [email protected] http://www.isely.net/cgi-bin/mailman/listinfo/pvrusb2
