* Kirti Wankhede (kwankh...@nvidia.com) wrote: > > > On 6/21/2019 2:16 PM, Yan Zhao wrote: > > On Fri, Jun 21, 2019 at 04:02:50PM +0800, Kirti Wankhede wrote: > >> > >> > >> On 6/21/2019 6:54 AM, Yan Zhao wrote: > >>> On Fri, Jun 21, 2019 at 08:25:18AM +0800, Yan Zhao wrote: > >>>> On Thu, Jun 20, 2019 at 10:37:28PM +0800, Kirti Wankhede wrote: > >>>>> Add migration support for VFIO device > >>>>> > >>>>> This Patch set include patches as below: > >>>>> - Define KABI for VFIO device for migration support. > >>>>> - Added save and restore functions for PCI configuration space > >>>>> - Generic migration functionality for VFIO device. > >>>>> * This patch set adds functionality only for PCI devices, but can be > >>>>> extended to other VFIO devices. > >>>>> * Added all the basic functions required for pre-copy, stop-and-copy > >>>>> and > >>>>> resume phases of migration. > >>>>> * Added state change notifier and from that notifier function, VFIO > >>>>> device's state changed is conveyed to VFIO device driver. > >>>>> * During save setup phase and resume/load setup phase, migration > >>>>> region > >>>>> is queried and is used to read/write VFIO device data. > >>>>> * .save_live_pending and .save_live_iterate are implemented to use > >>>>> QEMU's > >>>>> functionality of iteration during pre-copy phase. > >>>>> * In .save_live_complete_precopy, that is in stop-and-copy phase, > >>>>> iteration to read data from VFIO device driver is implemented till > >>>>> pending > >>>>> bytes returned by driver are not zero. > >>>>> * Added function to get dirty pages bitmap for the pages which are > >>>>> used by > >>>>> driver. > >>>>> - Add vfio_listerner_log_sync to mark dirty pages. > >>>>> - Make VFIO PCI device migration capable. If migration region is not > >>>>> provided by > >>>>> driver, migration is blocked. > >>>>> > >>>>> Below is the flow of state change for live migration where states in > >>>>> brackets > >>>>> represent VM state, migration state and VFIO device state as: > >>>>> (VM state, MIGRATION_STATUS, VFIO_DEVICE_STATE) > >>>>> > >>>>> Live migration save path: > >>>>> QEMU normal running state > >>>>> (RUNNING, _NONE, _RUNNING) > >>>>> | > >>>>> migrate_init spawns migration_thread. > >>>>> (RUNNING, _SETUP, _RUNNING|_SAVING) > >>>>> Migration thread then calls each device's .save_setup() > >>>>> | > >>>>> (RUNNING, _ACTIVE, _RUNNING|_SAVING) > >>>>> If device is active, get pending bytes by .save_live_pending() > >>>>> if pending bytes >= threshold_size, call save_live_iterate() > >>>>> Data of VFIO device for pre-copy phase is copied. > >>>>> Iterate till pending bytes converge and are less than threshold > >>>>> | > >>>>> On migration completion, vCPUs stops and calls > >>>>> .save_live_complete_precopy > >>>>> for each active device. VFIO device is then transitioned in > >>>>> _SAVING state. > >>>>> (FINISH_MIGRATE, _DEVICE, _SAVING) > >>>>> For VFIO device, iterate in .save_live_complete_precopy until > >>>>> pending data is 0. > >>>>> (FINISH_MIGRATE, _DEVICE, _STOPPED) > >>>> > >>>> I suggest we also register to VMStateDescription, whose .pre_save > >>>> handler would get called after .save_live_complete_precopy in pre-copy > >>>> only case, and will called before .save_live_iterate in post-copy > >>>> enabled case. > >>>> In the .pre_save handler, we can save all device state which must be > >>>> copied after device stop in source vm and before device start in target > >>>> vm. > >>>> > >>> hi > >>> to better describe this idea: > >>> > >>> in pre-copy only case, the flow is > >>> > >>> start migration --> .save_live_iterate (several round) -> stop source vm > >>> --> .save_live_complete_precopy --> .pre_save -->start target vm > >>> -->migration complete > >>> > >>> > >>> in post-copy enabled case, the flow is > >>> > >>> start migration --> .save_live_iterate (several round) --> start post > >>> copy --> > >>> stop source vm --> .pre_save --> start target vm --> .save_live_iterate > >>> (several round) > >>> -->migration complete > >>> > >>> Therefore, we should put saving of device state in .pre_save interface > >>> rather than in .save_live_complete_precopy. > >>> The device state includes pci config data, page tables, register state, > >>> etc. > >>> > >>> The .save_live_iterate and .save_live_complete_precopy should only deal > >>> with saving dirty memory. > >>> > >> > >> Vendor driver can decide when to save device state depending on the VFIO > >> device state set by user. Vendor driver doesn't have to depend on which > >> callback function QEMU or user application calls. In pre-copy case, > >> save_live_complete_precopy sets VFIO device state to > >> VFIO_DEVICE_STATE_SAVING which means vCPUs are stopped and vendor driver > >> should save all device state. > >> > > when post copy stops vCPUs and vfio device, vendor driver only needs to > > provide device state. but how vendor driver knows that, if no extra > > interface or no extra device state is provides? > > > > .save_live_complete_postcopy interface for post-copy will get called, > right?
That happens at the very end; I think the question here is for something that gets called at the point we stop iteratively sending RAM, send the device states and then start sending RAM on demand to the destination as it's running. Typically we send a small set of device state (registers etc) at this point. I guess there's two different postcopy cases that we need to think about: a) Where the VFIO device doesn't support postcopy - it just gets migrated like any other device, so all it's RAM must get sent before we flip into postcopy mode. b) Where the VFIO device does support postcopy - where the pages get sent on demand. (b) maybe tricky depending on whether your hardware can fault on pages of your RAM that are needed but not yet transferred; but if you can that would make life a lot more practical on really big VFO devices. Dave > Thanks, > Kirti > > >>> > >>> I know current implementation does not support post-copy. but at least > >>> it should not require huge change when we decide to enable it in future. > >>> > >> > >> .has_postcopy and .save_live_complete_postcopy need to be implemented to > >> support post-copy. I think .save_live_complete_postcopy should be > >> similar to vfio_save_complete_precopy. > >> > >> Thanks, > >> Kirti > >> > >>> Thanks > >>> Yan > >>> -- Dr. David Alan Gilbert / dgilb...@redhat.com / Manchester, UK
