Did you check timing with vacuum advance disabled/disconnected?  

Matthew




-----Original Message-----
From: [email protected] <[email protected]>
Sent: 27 January 2009 12:54
To: [email protected]
Subject: [Quantum Owners] Re: New cam fitted

Idle is terrible when cold but I think that's more to do with the auto 
choke, as it is fine when the choke is off. Seems ok at 800rpm with 12 
degrees on the ignition timing. I haven't messed about with the vernier 
pulley for the cam yet but did about 20 miles on the current set up and 
it seemed ok. Only thing I would say is that the ignition sounds over 
advanced on start up. I'll maybe give Burton Power a call and see what 
they recommend.



>----Original Message----
>From: [email protected]
>Date: 27/01/2009 11:20 
>To: "Quantum Owners Group"<[email protected]>
>Subj: [Quantum Owners] Re: New cam fitted
>
>
>Good job. It's always nice to get things going again when you have
>made significant changes.
>
>Is 800rpm on the low side for an engine with a more lumpy cam? I 
think
>my pinto should idle at 850 - 1150 with it's 285 cam.
>
>Ian
>
>On Jan 26, 10:15 pm, Bob Craig <[email protected]> wrote:
>> finally it stopped raining long enough for me to get the car 
outside
>> and get the front end back on. Took it for a test. Pretty happy 
with
>> the new cam (CVH22). No drop off at low revs but now has much more
>> poke higher up and pulls all the way to the red line.
>>
>> On 19 Jan, 22:29, Bob Craig <[email protected]> wrote:
>>
>> > Put a new rotor arm on - the old one was quite badly burnt. Also 
went
>> > back to basics with the carb set up and made sure the throttle 
cable
>> > was correctly adjusted Now running very nicely and ticking over 
at
>> > 800rpm, Need to get the front end back on and give it a road test 
but
>> > can't get it out of the garage for log enough due to the rain and 
snow
>>
>> > On 17 Jan, 22:32, Bob Craig <[email protected]> wrote:
>>
>> > > Finally got round to fitting my Kent cam today. It's a long 
time since
>> > > I had done one , so was a bit apprehensive, particularly as it 
was not
>> > > a standard one and required a bit more care in setting it up. 
It was a
>> > > relief when it started first time. Still needs a bit of fine 
tuning
>> > > with the vernier pulley and maybe a a tweek of the ignition 
timing but
>> > > so far so good
>>
>> > > Anyone who has one already fitted - what have you set your 
ignition
>> > > timing at?
>>
>> > > Bob Craig (Q2-267)- Hide quoted text -
>>
>> > - Show quoted text -
>>
>





What Tiscali can do for you - http://www.tiscali.co.uk/services
___________________________________________________





--~--~---------~--~----~------------~-------~--~----~
  You received this message because you are subscribed to the Google Groups 
"Quantum Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to 
[email protected]
For more options, visit this group at 
http://groups.google.com/group/quantumowners?hl=en

IMPORTANT NOTE: All information presented herewith is provided on an "As Is" 
basis, without warranty or the implication thereof. Neither the Quantum Owners 
Club nor the individuals associated with the Quantum Owners Club or in the 
preparation of the above information shall have any liability to any person or 
entity with respect to liability, loss, or damage caused or alleged to be 
caused directly or indirectly by the instructions contained within this or 
related message(s).
-~----------~----~----~----~------~----~------~--~---

Reply via email to