I have never played with mine. It is at 201 Dan Goldberg
-----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Jim Belisle Sent: Friday, February 19, 2016 1:13 PM To: Dan Goldberg Subject: [RBASE-L] - Re: SETTINGS MESSED UP I was able to reset the settings then adjusted them to what we were using. Question regarding the maxtrans setting. When it went back to the default settings this setting ended up at 201. Is that a good setting? We had our setting much lower than that. James Belisle Making Information Systems People Friendly Since 1990 -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Dan Goldberg Sent: Friday, February 19, 2016 2:41 PM To: Jim Belisle Subject: [RBASE-L] - Re: SETTINGS MESSED UP In rscope you can change/save the settings. Maybe compare a backup with the corrupted on and change accordingly. Dan Goldberg -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Jim Belisle Sent: Friday, February 19, 2016 12:37 PM To: Dan Goldberg Subject: [RBASE-L] - Re: SETTINGS MESSED UP It will not allow me to do that since the settings are not proper. Tried and all the happens is the settings box constantly pops up. I had to use the Task manager to get it to stop. James Belisle Making Information Systems People Friendly Since 1990 -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Dan Goldberg Sent: Friday, February 19, 2016 2:29 PM To: Jim Belisle Subject: [RBASE-L] - Re: SETTINGS MESSED UP Maybe try an unload all and see if that fixes it. Out db.all Unload all Out scr Rename the old db Run db.all Dan Goldberg -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Jim Belisle Sent: Friday, February 19, 2016 12:25 PM To: Dan Goldberg Subject: [RBASE-L] - Re: SETTINGS MESSED UP Shows the same settings (or lack thereof) as what I see when I look at the config settings choice. As I said, I have looked at the DB with RCOPE and that did not show any errors. It did however show that the settings were messed up. I have tried copying over to the directory a CFG file from another location. That did not work. I tried fixing the settings while in the explorer mode. It will not allow me to change anything. When I connect in the explorer mode, I get a WRITE error but it does allow me in the DB. But then the settings are all wrong. James Belisle Making Information Systems People Friendly Since 1990 [cid:[email protected]] From: [email protected] [mailto:[email protected]] On Behalf Of Bill Downall Sent: Friday, February 19, 2016 2:15 PM To: Jim Belisle Subject: [RBASE-L] - Re: SETTINGS MESSED UP Jim, At the R> prompt, what happens when you type SHOW [enter]? What happens when you type SHOW CHAR [enter]? Bill On Fri, Feb 19, 2016 at 3:11 PM, Jim Belisle <[email protected]<mailto:[email protected]>> wrote: I can open the DB in the explorer mode but I cannot change any of the CFG settings. These settings are very strange. There is a CFG file in the same directory as the DB. The CFG file has all the proper settings. I am stumped. James Belisle Making Information Systems People Friendly Since 1990 -----Original Message----- From: [email protected]<mailto:[email protected]> [mailto:[email protected]<mailto:[email protected]>] On Behalf Of Albert Sent: Friday, February 19, 2016 1:40 PM To: Jim Belisle Subject: [RBASE-L] - Re: SETTINGS MESSED UP It sounds as if the CFG file has disappeared. Find a backup and copy it back into the directory with the R:Base executable. Albert On 2016-02-19 12:04 PM, Jim Belisle wrote: > We are using RBASE 9.5_64 DB. > Just a few minutes ago our people started to get an ACCESS violation. > I haven't seen one of those for years. Once that message came up, others > could not get into the DB. > After I was informed of the problem (I am odd site) I tried connecting in the > Explorer mode. > It acted like it was connected but when I looked at the settings, they were > all messed up. > None of the below areas had a setting at all MANY, QUOTES, PLUS, NULL, > SINGLE, SEMI, DELIMIT, CURRENCY > > I connect with RSCOPE and no errors were found in any area. > Any Blue's clues as to how to fix this? > > James Belisle > > Making Information Systems People Friendly Since 1990 > [cid:[email protected]] > >
